Modeling Light Signals Using Data from the First Pulsed Neutron Source Program at the DUNE Vertical Drift ColdBox Test Facility at CERN Neutrino Platform

2026-03-19T14:55:27Z

In this paper, we present a first quantitative test of detected light signals produced in a pulsed neutron source run in a small vertical drift LArTPC at the CERN neutrino platform ColdBox test facility. The ColdBox cryostat, detectors, neutron sources, and particle interactions are modeled and simulated using Fluka. A good agreement is found in the detected number of photoelectrons, with values below 650 photoelectrons in both data and simulation, for all four X-ARAPUCA photodetectors on the cathode in the LArTPC. A time constant is also fitted from the neutron-beam-off light signal spectrum and found consistent between data and MC. Several important systematic effects are discussed and serve as guides for future runs at larger LArTPCs.

XCOM: Full Mesh Network Synchronization and Low-Latency Communication for QICK (Quantum Instrumentation Control Kit)

2026-03-19T14:41:55Z

Quantum computing experiments and testbeds with large qubit counts have until recently been a privilege afforded only to large companies or quantum technologies where scaling to hundreds or thousands of qubits does not require a substantial increase in quantum control hardware (neutral atoms, trapped ions, or spin defects). Superconducting and spin qubit testbeds critically depend on scaling their control systems beyond what a single electronics board can provide. Multi-board control systems combining RF, fast DC control, bias, and readout require precise synchronization and communication across many hardware and firmware components. To address this, we present XCOM, a network that synchronizes QICK boards and the absolute clocks governing quantum program execution to within 100 ps, free of drift and loss of lock. XCOM also provides deterministic, all-to-all simultaneous data communication with latency below 185 ns. Like QICK itself, XCOM is compatible with a broad range of qubit technologies and is designed to scale to large systems.

A Minimal-Component 100 MHz Full-Duplex Digital Link Over a Single Coaxial Cable for Laboratory Instrumentation

2026-03-19T12:51:29Z

We present a minimal-component bidirectional digital interconnect that enables simultaneous transmission and reception of baseband logic signals over a single coaxial cable. The circuit consists of a passive resistive hybrid providing matched line termination and directional separation, a single CMOS logic gate as driver, and a commercial LVDS receiver used as a differential comparator. No active echo cancellation, calibration, or transformer coupling is required. An analytical treatment of the hybrid network is used to determine the system parameter that maximizes the received signal amplitude. SPICE simulations predict deterministic timing errors caused by incomplete separation of transmitted and received signals. Experimental measurements confirm the predicted deterministic jitter and show good agreement with the simulation results. For typical laboratory coaxial cables up to 6 m, the measured peak-to-peak edge timing error remains below 1 ns. A bidirectional transmission experiment with randomized data at 250 MBaud demonstrates a clearly open eye diagram and confirms reliable full-duplex operation. Due to its simplicity and compatibility with existing coaxial infrastructure, the proposed approach may be useful in laboratory and detector environments where cable routing or feedthrough density is constrained.

Spatial resolution improvement of PICOSEC Micromegas precise timing detectors

2026-03-19T10:32:08Z

The combination of a Cherenkov radiator with a semi-transparent photocathode and a Micromegas based amplification stage allows PICOSEC Micromegas detectors to achieve a time resolution of better than 15ps. While tileable prototypes with 10x10 channels feature 1x1 cm^2 readout pads, finer readout granularity can be used to improve the spatial resolution. We report on the study of high readout granularity PICOSEC Micromegas prototypes which achieve around 0.5mm spatial resolution with 3.5mm large pads. No significant improvement was found when readout pad size was further reduced to 2.2mm. The timing resolution of the leading pad was found to be slightly degraded but remained better than 20ps for a medium granularity prototype. The achieved spatial resolution can enable PICOSEC Micromegas to be used as precise timing and moderate resolution tracking detector simultaneously.

Design and implementation of a high-density sub-nanosecond timing system for a C-band photocathode electron gun test platform

2026-03-19T07:57:49Z

This paper presents the design and implementation of a high-density, deterministic trigger distribution system tailored for the C-band photocathode electron gun test platform at the Southern Advanced Photon Source (SAPS). Implemented within a scalable 6U VME modular architecture, the system achieves high-density integration by consolidating a master controller, clock distribution network, and 80 heterogeneous output channels into a single chassis. This design leverages a high-performance FPGA core combined with custom backplane interconnections to establish a master-slave topology, significantly reducing the system footprint compared to stacked standalone generators. To guarantee timing determinism in high-noise environments, precise placement and timing constraints are applied to the FPGA logic, while optical isolation is employed to mitigate electromagnetic interference. Furthermore, a dual-channel SFP optical signaling architecture enables seamless expansion to 160 synchronized channels. A remote control framework based on a serial server and a virtual machine Input/Output Controller (IOC) facilitates flexible configuration. Performance tests demonstrate adjustable trigger frequencies from 1 Hz to 100 Hz, with delays and pulse widths tunable from 0 to 10 ms at a resolution of 10 ns (or the RF period). The local electrical output exhibits an ultra-low RMS jitter of 6.55 ps (60 ps peak-to-peak). For remote optical distribution, the system maintains a sub-nanosecond RMS jitter of 119.5 ps, with peak-to-peak variation confined to 1 ns due to the combined effects of transceiver optoelectronic conversion (utilizing HFBR-1414T/2412T modules) and fiber transmission. The system has been successfully commissioned and is currently in reliable routine operation, verifying the architecture as a robust, highly integrated, and cost-effective solution for compact accelerator facilities.

Stability of Charge Collection Efficiency and Time Resolution in 4H-SiC PIN Diodes Under X-ray Irradiation

2026-03-19T07:02:25Z

This study evaluates the radiation tolerance of a 4H-SiC PIN detector under X-ray irradiation up to \SI{2}{MGy} (Si) at \SI{160}{keV}. The detector features a fully epitaxial vertical PIN structure with mesa terminations and field plates. Comprehensive pre- and post-irradiation characterization includes I-V/C-V measurements, charge collection efficiency (CCE) and timing resolution tests using $β$-particles ($^{90}$Sr). After \SI{2}{MGy} irradiation, the reverse leakage current remains at an ultralow level of $\sim 10^{-11}$ \si{A/cm^2} at \SI{-300}{V} with negligible degradation. C-V characteristics are basically consistent, with full depletion at \SI{~130}{V}. CCE for $β$-particles decreases by less than 5\%. The detector maintains good timing resolution: \SI{21}{ps} before and \SI{31}{ps} after irradiation, with jitter increasing moderately. These results demonstrate stable performance under extreme X-ray exposure, highlighting the detector's potential for radiation-hard applications in high-energy physics, space missions, and nuclear reactor monitoring.

Study of few-electron backgrounds in the LUX-ZEPLIN detector

2026-03-18T23:45:10Z

The LUX-ZEPLIN (LZ) experiment aims to detect rare interactions between dark matter particles and xenon. Although the detector is designed to be the most sensitive to GeV/$c^2$--TeV/$c^2$ Weakly Interacting Massive Particles (WIMPs), it is also capable of measuring low-energy ionization signals down to a single electron that may be produced by scatters of sub-GeV/$c^2$ dark matter. The major challenge in exploiting this sensitivity is to understand and suppress the ionization background in the few-electron regime. We report a characterization of the delayed electron backgrounds following energy depositions in the LZ detector under different detector conditions. In addition, we quantify the probability for photons to be emitted in coincidence with electron emission from the high voltage grids. We then demonstrate that spontaneous grid electron emission can be identified and rejected with a high efficiency using a coincident photon tag, which provides a tool to improve the sensitivity of future dark matter searches.

Characterization of thin optical filters for high purity Cherenkov light readout from scintillating crystals

2026-03-18T21:00:20Z

A hybrid dual-readout calorimeter concept, comprising both electromagnetic and hadronic sections, has recently been proposed to meet the performance requirements of experiments at future e$^{+}$e$^{-}$ colliders. The front compartment consists of a homogeneous electromagnetic calorimeter made of high-density crystals, each coupled to a pair of Silicon Photomultipliers (SiPMs) providing the simultaneous readout of scintillation and Cherenkov light. To efficiently detect Cherenkov photons in the presence of dominant scintillation signals, an optical filter is placed in front of one of the two SiPMs to suppress photons in the wavelength region corresponding to that of scintillation emission. In this study, PWO, BGO, and BSO crystals with different dimensions were tested to measure their scintillation light yield and decay time, as well as their transmission and emission spectra. A set of $\sim 100~\rm μm$-thick optical filters was also characterized by measuring their transmittance curves. The experimental results were used to model and estimate the expected filter performance in attenuating scintillation light for the various crystals. The performance of each filter was experimentally validated by measuring the crystal light output with and without the filter using a $^{22}$Na radioactive source and a LYSO:Ce crystal, confirming the accuracy of the calculations. The results show that interference filters are unsuitable for this application because their transmittance strongly depends on the photon incidence angle. Conversely, two absorptive long-pass filters with cutoff wavelengths around 590 nm were found to block more than 99% of the scintillation light from PWO crystals, satisfying the calorimeter specifications.

Low Energy Phonon Bursts Created By Fast Neutron Damage

2026-03-18T17:33:29Z

Solid state athermal phonon calorimeters used in the search for low mass dark matter or coherent neutrino-nucleus interactions have long observed a large excess of events below several hundred eV. The relaxation of damage created by the interaction of fast cosmic ray neutrons with the detector has been proposed as a source of these excess events. By comparing neutron exposed detectors to control detectors, we report the first measurement of phonon bursts caused by damage created by fast neutrons. Differences in the spectral shape, the rate dependence on thermal history, and the observed spectral rate scaled to the neutron exposure between irradiated and control detectors suggest that our observed LEE backgrounds are not dominated by neutron damage-induced phonon bursts.

Evaluation of PID Performance at CEPC and Optimization with Combined dN/dx and Time-of-Flight Data

2026-03-18T15:56:13Z

Charged-hadron identification (PID) is a critical requirement for the physics program of the Circular Electron-Positron Collider (CEPC). The baseline detector relies on ionization measurements from a time projection chamber (TPC), which provides strong PID capability at low momenta but becomes less effective at higher momenta. In this work, we investigate an extended PID strategy that combines dN/dx information from the TPC with time-of-flight (ToF) measurements from a silicon-based outer tracker (OTK) and a timing-upgraded inner tracker (ITK) equipped with AC-LGAD sensors. A unified discriminant is constructed to exploit the complementary sensitivity of ionization and timing observables. The performance is evaluated using simulated $Z \to q\bar{q}$ events, focusing on kaon identification in the presence of dominant pion backgrounds. The combined configuration significantly improves both efficiency and purity over a broad kinematic range, extending PID capability to both sub-GeV and multi-GeV regions. These results highlight the impact of precision timing on tracking detectors and demonstrate a viable path to enhanced PID performance for future lepton colliders.

Design and First Results of COFFEE3: A 55nm HVCMOS Pixel Sensor Prototype for High-Energy Physics Applications

2026-03-18T04:16:37Z

Motivated by the stringent requirements of the Upstream Pixel (UP) tracker in the LHCb Upgrade II and the Inner Tracking detector (ITK) of the Circular Electron Positron Collider, the COFFEE series of pixel sensor chips have been developed using a 55nm High-Voltage CMOS (HVCMOS) process. The primary objective is to achieve a time resolution of a few nanoseconds under a hit density of up to 100 MHz/cm$^2$, while maintaining fine spatial resolution ($\sim$10 $μ$m) and reasonable power consumption ($<$200 mW/cm$^2$). Building on the process validation of the COFFEE2 prototype, this work presents the design and preliminary test results of COFFEE3-a prototype integrating two distinct readout architectures. Architecture 1, tailored for the current triple-well process, adopts NMOS-only in-pixel circuitry and innovative column-level readout to handle high hit densities. The time walk of pixel-level signal is controlled within 10 ns, and the Time of Arrival (TOA) and Time over Threshold (TOT) are measured with a system clock with the period of 25 ns in peripheral circuits. Architecture 2, developed for future possible processes with p-type buried layer isolation, features pixel-level time measurement and storage. A chip-level Time-to-Digital Converter (TDC) is used and the part of Voltage-Controlled Delay Line (VCDL) is copied in each pixel to get a high time resolution. The TOA resolution is estimated to be 4.2 ns and the TOT resolution 8.4 ns. COFFEE3, with a layout size of 3$\times$4 mm$^2$, was manufactured and has undergone preliminary tests. Charge injection tests for analog circuits, and laser tests for full readout chains, confirm that both architectures operate as expected. Next step work will focus on characterizing key performance such as the timing resolution, radiation hardness, and tracking performance of minimum ionising particles.

Optimal operating parameters for next-generation xenon gas time projection chambers

2026-03-17T22:12:22Z

The next-generation of $0νββ$ searches are targeting half-life sensitivities towards 10$^{27}$--10$^{28}$ years. Gaseous xenon time projection chamber (GXeTPC) detectors may be able to meet this challenge due to their excellent energy resolution and background rejection power through event visualization. This paper explores how the design choices of a next-generation GXeTPC time projection chamber can impact the overall performance of the experiment. We study the performance of systems using xenon enriched in the isotope $^{136}$Xe or natural xenon, focusing on scenarios that incorporate one tonne of $^{136}$Xe isotope. The detector size, copper shielding mass, energy resolution, density and corresponding levels of diffusion are surveyed to evaluate the overall performance dependencies on these parameters. A detector optimized for using enriched xenon is preferred over natural, due primarily to a factor of 10 lower background rate driven by the large intrinsic backgrounds introduced by the copper shielding used in the detector. The performance of three types of gas TPC technologies was also explored based on different gas additives used to reduce diffusion to different levels. For all TPC technologies, we find background rates of a fraction of a count per tonne year in the region of interest are achievable. These performance levels are contingent on suitable energy resolution and event position placement in the drift direction being achieved for the specific detector technology. Performance for enriched xenon TPCs varies mildly with pressure in the range 5 to 25 bars, reaching background levels below 0.2 events/tonne-year. Performance at one bar is worse by approximately a factor of four. When considerations for the construction of the detector in addition to the selection performance are included, there may be no clearly optimum pressure.

Accelerating Structure-Property Relationship Discovery with Multimodal Machine Learning and Self-Driving Microscopy

2026-03-17T18:08:57Z

Microscopy combined with local spectroscopy is widely used to correlate nanoscale structure with functional properties in materials, but conventional measurements rely heavily on human-selected sampling locations and predefined targets, limiting dataset diversity and the potential for discovery. Here, we present a framework that integrates autonomous microscopy with a dual-novelty deep kernel learning (DN-DKL) for adaptive data acquisition and a dual variational autoencoder (VAE) for representation learning. DN-DKL actively guides the microscopy toward structurally and spectroscopically novel regions, enabling efficient collection of large spectral datasets. Dual-VAE embeds local structure and spectroscopic responses into a shared latent manifold that serves as a structure-property relationship map. We applied this framework for the investigation of halide perovskite films using conductive atomic force microscopy. The results reveal distinct hysteresis behaviors that are linked to specific nanoscale structural motifs, including grain boundary junction points that show hysteresis under different bias conditions and asymmetric grain boundaries that suppress charge transport. This framework establishes a general strategy that leverages the complementary strengths of self-driving microscopy, machine learning, and human expertise to accelerate scientific discovery in functional materials.

Coincidence Algebra Bundle for Decay Quivers: An Algebraic Approach to Gamma-ray Spectroscopy

2026-03-17T16:22:57Z

Motivated by the need for a more comprehensive algebraic structure to calculate coincidence probabilities of a general decay scheme for gamma ray spectroscopy, we model the decay scheme, rather naturally, as a quiver through which we define a decay quiver. The path algebra of quivers is the underlying, more general, algebra for transition matrices that is typically used in modeling decay schemes. The path algebra allows for concatenation of transitions which affords the calculation of cascade probabilities. We extend the path algebra to allow for the multiplication of non-composable paths, i.e., transition that don't directly share a level connecting them. We define the coincidence algebra as the algebra that allows for such an extension and realize it as the fibres for a coincidence algebra bundle, the base space of which is the path algebra where decay schemes live. A given decay schemes coincidence probabilities are calculated on its fibre. \textit{Detection maps} are defined as maps on the base space that map transition probabilities to detected probabilities.

Investigating Ultra-Low Energy Ionization Yield from Nuclear Recoils in Semiconductor Detectors via Molecular Dynamics Simulations

2026-03-17T15:56:10Z

Nuclear recoil ionization yield constitutes a critical uncertainty source in low-energy detection for dark matter (DM) and coherent elastic neutrino-nucleus scattering (CE$ν$NS) experiments. We present a novel methodology employing molecular dynamics simulations to assess ionization yields in crystalline semiconductor detectors. This non-parameterized approach resolving inherent limitations of traditional Lindhard model through explicit incorporation of crystal condensed matter effects, facilitating a seamless reliability from high-energy ($E>10$\,keV) to electron-hole pair (EHP) regimes. Our model achieves the best agreement with experimental data in silicon to date, especially at the minimal energy level of a single EHP. Meticulously consideration of ion transport mechanisms reveals fundamental ionization yield distributions, superseding conventional single-value models. The distributional paradigm extends the DM-nucleon elastic scattering exclusion limit to 0.29\,GeV/$c^2$ under single-EHP sensitivity. We further report advancements in modeling quantum effects and channeling phenomena affecting ionization yields in high-purity germanium detectors.