Design, construction, and operation of a 30-ton Water-based Liquid scintillator detector at Brookhaven National Laboratory

2026-09-09T17:51:49Z

Water-based Liquid Scintillator (WbLS) was proposed over a decade ago as a novel detector medium that might allow the separation and tuning of the relative ratio of the Cherenkov and scintillation signals. A detector employing this technology could support large-scale neutrino detection over both the GeV and MeV energy regimes, while its metal-loading capability could provide an effective means of neutron tagging. WbLS is attractive for two reasons. It can be deployed in very large detectors. It also allows in-situ tuning of the scintillator concentration, and hence the ratio of Cherenkov to scintillation light. Neither pure water Cherenkov detectors nor conventional liquid scintillator detectors offer this capability. At Brookhaven National Laboratory (BNL), two prototypes have been built for understanding WbLS properties and stability, with masses of 1-ton and 30-ton, respectively. We present here the 30-ton prototype detector design, installation, and initial operation including the real-time observation of a transient optical response during the staged scintillator injection. Results from the analysis of data collected in the two detectors will follow in separate publications.

Real-Time Requirements and Transferability in Compton Imaging: From the Detector Chain to the Application

2026-09-09T14:46:09Z

Compton cameras are proposed for tasks whose value decays with delay: verifying a range during irradiation, guiding an intervention, characterising an inaccessible volume, surveying a band no telescope covers. Whether a device can serve such a task is settled by the composition of its whole chain, while the literature that would answer the question is organised by stage -- so claims made at application level routinely rest on evidence obtained at component level. This review walks that chain, asking at each stage what binds first and what a reader can determine from the published text, and then asks what governs whether a capability transfers between groups and between application domains. The evidence is of two kinds: 83 full texts scored in context against defined markers, and, for five application domains measured alike, the size of the receiving literature, of the need it states, of the incumbent and of deployment commitment. Performance is reported at one operating point in 65 of 83 full texts, with count rate swept in none: the field reports values where transfer requires gradients. An accelerator is used in 39 works and a learned model in 31, while separability is discussed in 28, a memory footprint given in 9, and the cost of a precomputation or the inference time of a model in none. Across domains, neither the size of the receiving literature, nor of the incumbent, nor of the stated need orders the domains as deployment commitment does, while whether the incumbent can serve the task at all, and how many domain boundaries the output must cross, do so consistently. The distribution of publication is close to the inverse of the distribution of deployment commitment. We give the quantities a report must contain for a third party to judge whether a method fits an application it was not built for.

Optimization and Underground Implementation of the KAPAE Phase II Detector for an Invisible New Particle Search in Positronium Decay

2026-09-09T14:43:33Z

The KAPAE Phase II detector was developed to search for invisible decays of positronium as a probe of physics beyond the Standard Model. The detector geometry was optimized with Geant4 simulations, and the scintillation and readout performance were evaluated experimentally. The temperature dependence of the BGO scintillator and several readout configurations were studied to find the operating condition giving the best energy resolution. The background level was then measured both at the surface and underground. At the surface, the positron-gamma coincidence background was of order 1 Hz, with occasional bursts up to about 65 Hz. Underground, it decreased to below about 3 \times 10^{-4} Hz, more than three orders of magnitude lower.

Post-fabrication trimming of a 1024-pixel, single-photon counting, Microwave Kinetic Inductance Detector array with a pixel pitch of 150 micron

2026-09-09T13:24:07Z

Microwave Kinetic Inductance Detectors are superconducting resonators capable of single-photon counting with energy resolving capability at visible and near-infrared wavelengths. Their zero read noise, extremely low dark counts, and compatibility with frequency-division multiplexing make them well suited for large imaging arrays. The detector yield of these arrays is often limited by the fabrication-induced frequency scatter leading to resonator collisions. We find that the tight packing of the pixels can add significant frequency scatter as well. We developed a post-fabrication correction method that is suitable for tightly packed arrays with a pixel pitch of $150\ \mathrm{μm}$. We demonstrate this method on a 1024-pixel array multiplexed on a single octave of readout bandwidth and show a reduction in frequency scatter from $1.1\times 10^{-2}$ to $3.5\times 10^{-4}$ and an increase in yield from $76\%$ to $94\%$.

Development of Ultrafast and Radiation-Hard GAGG for the Next-Generation of High-Energy Physics Calorimeters

2026-09-09T12:49:14Z

The evolution of High Energy Physics (HEP) toward future collider experiments with High Luminosity (HL), such as the HL-LHC, requires the development of scintillating materials that combine high density, excellent radiation hardness and an ultrafast response. While Cerium-doped Gadolinium Aluminum Gallium Garnet (GAGG:Ce) offers a very high light yield and resilience to irradiation, its typical decay time of approximately 50-60 ns may lead to pile-up effects in high-rate environments. In this paper, we report on the development and multi-stage characterization of various accelerated GAGG compositions optimized for timing performance and grown by Crytur. By taking advantage of divalent co-doping to engineer the scintillation kinetics, we achieved an effective decay time (tau_d,eff) down to 5.5 ns while maintaining a competitive light yield of several thousand photons per MeV. Laboratory characterization demonstrates that the time resolution under gamma-ray excitation is comparable to commercial GAGG, while the time resolution measured with 120 GeV pions reaches performance levels comparable to state-of-the-art LYSO:Ce,Ca. After a 1 MGy proton irradiation campaign the material retains most of its optical transmission. The results confirm that this ultrafast GAGG composition is a viable candidate for the next generation of HEP calorimetry and timing detectors.

A unified quantum electrical platform for synchronous metrological realization of volt, ohm and ampere

2026-09-09T09:49:49Z

A co-located integration quantum electrical standard is essential to reduce reliance on distributed traceability in high-accuracy metrology, especially for portable and on-site use. Metrologically, realizing any two of voltage, resistance, and current is sufficient, as the third follows from Ohm's law. The combination of Josephson voltage and quantum Hall resistance offers better uncertainty, but conflicts with the tesla-level field for quantum Hall and near-zero field for Josephson operation. Here we report a compact unified platform enabling co-realization of quantum voltage and resistance in a single cryostat near 4 K, with quantum current derived via Ohm's law. A hierarchical magnetic shielding with staged attenuation and spatial confinement allows 6 T and below 50 nT to coexist within 270 mm axial separation with negligible cross-coupling. In integrated operation, the Josephson and quantum Hall subsystems agree with expected quantized values within relative standard uncertainties of 2.6E-9 and 1.4E-8, respectively. Linking them via an improved cryogenic current comparator realizes a 50 μA quantum current with relative uncertainty of 6.6E-8. These results demonstrate that three basic electrical units can be synchronously realized with superior metrological consistency on a single integrated platform, offering a viable transition from distributed calibration chains toward compact-integrated quantum-based realization.

A Six-Quadrupole Diamagnetic Suspension Architecture for Ultra-Sensitive Space Accelerometry

2026-09-09T09:09:46Z

This paper proposes a novel inertial sensor based on a solid diamagnetic cubic test mass passively suspended by a symmetric configuration of six magnetic quadrupoles. Designed specifically for microgravity environments, this system eliminates the mechanical noise and hysteresis inherent in elastic suspensions, as well as the complexity associated with electrostatic suspension systems. We provide an analysis of the magnetic intrinsic noise floor imposed by eddy current damping, alongside ground-based preliminary experimental results demonstrating potential sensitivities in the order of the $10^{-10} \text{ m/s}^2/\sqrt{\text{Hz}}$ regime.

Operation of a negative ion gas time projection chamber without electronegative fill gases

2026-09-09T07:50:12Z

The high fidelity reconstruction of particle tracks in micropatterned gaseous time projection chambers renders this technology ideal for future rare-event searches, including direction-sensitive dark matter experiments. Large drift distances are typically required for such experiments, so that the overall spatial resolution is limited by diffusion. Negative ion drift exhibits lower diffusion than electron drift and is thus an attractive option for realising a large-scale detector. The use of electronegative gases to create negative ions introduces technical challenges, most notably a reduction in gain when compared to conventional gas mixtures. In this study, we demonstrate a new method for negative ion generation via dissociative electron attachment using the conventional molecular fill gas CF$_4$. Our optical measurements of negative ion drift indicate electron attachment lengths of $<$1 mm and comparable gain to electron avalanches. The individual negative ion avalanches were also time-resolved, allowing the number of ions reaching the readout to be counted. We measure an improved energy resolution by single ion counting, relative to an integrated electron avalanche signal measured under identical gain conditions.

Extended High-Mass Axion Search with an Auxetically Tuned Higher-Order-Mode Cavity

2026-09-09T05:02:05Z

Conventional high-mass axion haloscopes based on the TM$_{010}$ mode lose detection volume as the resonant frequency increases. We report an extended axion search using a dielectric-restored TM$_{020}$ cavity haloscope with symmetry-preserving auxetic tuning based on a single-degree-of-freedom mechanical architecture. Using a near-quantum-limited microwave receiver, we searched a frequency range of 4.98-5.07 GHz and exclude axion-photon couplings with sensitivity approaching the KSVZ benchmark. Together with two earlier searches, the present scans extend a multi-scan program based on this architecture, yielding nearly 300 MHz of contiguous high-mass axion coverage over 4.98-5.27 GHz, the first broad search reported with a single higher-order-mode haloscope. This work establishes higher-order-mode cavities as a practical, scalable route beyond the TM$_{010}$ volume penalty.

Spectral Discrimination of Deposited Gamma-Ray Energies in a Simulated CeBr$_3$ Scintillator

2026-09-09T02:56:18Z

We show that wavelength measurements of individual detected optical photons may provide additional information about gamma-ray energy deposited in a CeBr$_3$ crystal when the detected-photon-count distributions overlap for nearby gamma-ray energies. Monoenergetic 662 and 629 keV gammas are used in a Geant4 simulation of a $25\times25\times20~\mathrm{mm^3}$ CeBr$_3$ crystal. Assuming a light yield of $6.0\times10^4$ photons/MeV, a wavelength-independent photon-detection efficiency of 30%, and a wavelength resolution of $σ_λ=40$ nm, we find that the fraction of photons reconstructed above 385 nm gives an event-level separation of $\sim$ 2 standard deviations between the 662 and 629 keV event populations selected within the same $\sim$ 1%-wide detected-photon-count interval. No timing or reconstructed interaction-position information is used. The result demonstrates, within the present simulation model, that event-dependent optical spectra can retain energy information beyond an undifferentiated photon count.

Development and demonstration of the Korea ALICE Telescope using electron beams at KEK PF-AR

2026-09-08T23:07:09Z

The development of ultra-low-mass, high-precision vertex detectors is a key requirement for future collider experiments and motivates extensive research and development of novel silicon tracking technologies. In this work, we present the development and beam-test demonstration of the Korea ALICE Telescope (KATS), a silicon-tracking telescope designed to support R&D on next-generation cylindrical vertex detectors, such as the proposed ALICE ITS3 upgrade. The telescope consists of six ALPIDE Monolithic Active Pixel Sensors (MAPS) used as reference tracking planes, a bent ALPIDE sensor serving as the device under test, and a scintillating-fiber-based trigger system, all housed in a light-tight modular enclosure. This setup enables precise track reconstruction and detailed performance studies of both planar and curved silicon sensors. Beam tests were carried out using high-energy electron beams at the KEK Photon Factory Advanced Ring (PF-AR). The telescope system operated stably under realistic beam conditions, and its tracking performance was successfully validated. The bent ALPIDE sensor was operated at a bending radius of approximately 18 mm, consistent with ITS3's design goals, without any observable degradation in detection performance. The measured results confirm that the KATS provides a versatile and reliable platform for studies of curved MAPS technologies, alignment precision, and tracking performance. These results provide important experimental validation of key technologies for future low-mass cylindrical silicon vertex detectors and establish KATS as a valuable facility for ongoing and future detector R&D.

Superconducting Flux Memory for Cryogenic Applications

2026-09-08T22:33:12Z

We report the development of flux memory for use with superconducting circuits. This technology stores persistent currents in superconducting loops on-chip to be used to provide flux biasing for superconducting circuits, like qubits. We developed three types of flux memory and draw comparisons among them for circuit design. We demonstrate the utility of flux memory by using an in-situ flux detector and characterize each approach and further demonstrate that once flux is set in a memory cell, benchtop DC control sources can be powered off, leaving the on-chip flux bias in place. We propose that flux memory can be arranged in a two-dimensional configuration to multiplex control signals and reduce how line counts scale (N^2 devices -> 2N control lines), and our experimental results pave the path to the proposed scalability. We demonstrate the use of flux memory to flux bias a transmon qubit and show the tunability of the qubit state to a target frequency which remained stable on-chip for 20 hours.

Intrinsic time resolution of a hexagonal BC404 scintillator: A Monte Carlo study of interaction geometry and optical reflectivity

2026-09-08T20:11:11Z

Time resolution is an important parameter in particle detectors, as it determines their ability to distinguish between two temporally separated events. It can be decomposed into electronic and intrinsic contributions, the latter being influenced by scintillation, optical transport, detector geometry, particle type and energy, and the sensitive area of the photosensor. In this work, a Monte Carlo simulation based on Geant4 is used to investigate the intrinsic time resolution of a hexagonal BC404 plastic scintillator. The analysis includes the evaluation of the optical-photon distribution over the hexagonal surfaces and the characterization of the intrinsic time resolution for different interaction configurations. The intrinsic time resolution is investigated using muons as cosmic-ray proxies with energies ranging from 4~GeV to 1~TeV. In addition, the effect of surface reflectivity on optical-photon transport and timing performance is studied for reflectivities ranging from 0\% to 100\%. The results show that the intrinsic time resolution exhibits little dependence on the incident muon energy, while a clear dependence on the interaction position is observed. Furthermore, although the number of detected photons varies with the interaction position and surface reflectivity, the intrinsic time resolution is not solely determined by photon statistics, indicating that optical transport and geometrical effects play an important role in the timing performance. Across the investigated configurations, intrinsic time resolutions ranging from approximately 15 to 100~ps are obtained. These findings highlight the importance of the interaction position, optical transport, photon statistics, and surface reflectivity in determining the timing performance of hexagonal plastic scintillators and provide guidance for the optimization of their optical properties and geometry for timing-sensitive applications.

Characterization of CRYO ASIC for charge readout in the nEXO experiment

2026-09-08T19:03:14Z

nEXO is a proposed next-generation experiment searching for the neutrinoless double beta decay of $^{136}$Xe using a tonne-scale liquid xenon (LXe) time projection chamber (TPC). To image the ionization signals from events in the liquid xenon, the detector will employ metallized fused-silica charge collection tiles instrumented with cryogenic application-specific integrated circuits (ASICs), referred to as CRYO ASIC, which are designed to operate directly in LXe to minimize input capacitance and pick-up noise. Here we present the performance of the CRYO ASIC mounted on an auxiliary printed circuit board and evaluated both in a cryogenic environmental chamber and in a dedicated LXe test stand. We demonstrate that the ASICs achieve the desired performance at liquid xenon temperatures, showing a gain stability better than 0.2% over 24-hour operation and reliable in-situ calibration using an on-chip pulser. In the LXe test stand, we show that boiling caused by the chip heat dissipation can be mitigated by operating the system above ~0.1 MPa. The in-LXe noise measured agrees with simulation, which indicates it the $150~e^-$ design requirement can be satisfied. These results establish CRYO ASIC as a viable low-noise in-LXe charge readout solution for nEXO.

Non-destructive 3D doping imaging of silicon sensors

2026-09-08T14:03:59Z

Silicon sensors are the foundational detection medium for X-rays and charged particles. While their bulk dopant distribution determines device performance, it is conventionally assumed homogeneous because traditional profiling is destructive, spatially restricted, and insensitive at the relevant concentrations. Here we introduce a non-destructive 3D doping imaging technique that turns the readout electronics of a charge-integrating hybrid pixel detector into a massively parallelized capacitance-voltage profiler. With a few tens of micrometres of 3D resolution over wafer-scale areas at concentrations on the order of $10^{11}$ cm$^{-3}$, we image the bulk doping concentration of operational sensors. Macroscopically, we resolve depth-evolving concentric doping rings; microscopically, we uncover scattered doping anomalies that distort local electric fields. The rings modulate the depletion voltage, while the anomalies disrupt local charge collection, a previously overlooked cause of pixel yield and performance degradation. By bridging manufacturing signatures with microscopic defects, this approach provides a non-destructive framework for sensor characterization and yield optimization.