https://arxiv.org/api/MQhQVwM3Ut8ebIieapGtOFwXhiI 2026-09-10T19:11:55Z 35174 30 15 http://arxiv.org/abs/2609.07543v1 2026-09-07T14:27:32Z

In this article, we study the flow induced by crystallization of sodium chloride in sessile droplets. We measure flow velocities on the order of 1 $\mathrm{cm.s^{-1}} during crystallization, two orders of magnitude higher than those reported in previous studies. We show that this discrepancy is due to surface contaminants in earlier experiments. Numerical simulations reveal that in the clean case, the flow is driven by Marangoni stresses, whereas it is density- driven in the contaminated case. Consequently, droplet cleanliness significantly influences the flow which, in turn, determines the growth rate of crystals.

2026-09-07T14:27:32Z Théophile Gaichies Javier Martínez-Puig Javier Rodríguez Rodríguez http://arxiv.org/abs/2601.03157v3 2026-09-07T14:06:47Z

When a large air cavity breaks in a turbulent flow, it goes through very large deformations and cascading events of new interface formation, including elongated filaments and bubbles over a wide range of scales, with their rate of formation controlled by turbulence and capillary processes. We experimentally investigate the effects of surfactants and salt on the fragmentation of a large air cavity, and observe a five fold increase of the number of bubbles being produced in some cases. We characterize the bubble size distribution resulting from successive break-ups in such transient configuration. For bubbles larger than the Hinze scale $d_H$ (defined as the balance between surface tension and turbulence stresses), we observe that bubble size distributions remain unchanged for all solutions tested. For bubbles below $d_H$, however, we observe an increase of the number of bubbles produced and an associated steepening of the bubble size distribution upon the addition of surfactant or salt. This later effect is only visible for surfactants with an adsorption timescale that is fast enough compared to the rate at which new interfaces are being generated by turbulence.

2026-01-06T16:33:34Z Zhan Wu Tristan Aurégan Luc Deike http://arxiv.org/abs/2609.07472v1 2026-09-07T13:28:22Z

This work presents a comparative analysis of Reduced-Order Models (ROMs) applied to incompressible fluid dynamics within geometrically parametrized domains. Two distinct reduced-order solution strategies are investigated and compared: a monolithic coupled solver and a segregated SIMPLE-based algorithm. Their performance is assessed on two steady, two-dimensional benchmark cases: a lid-driven cavity flow and a flow past a cylindrical obstacle. The two algorithms are compared in terms of fields evaluation and aerodynamic coefficients prediction. The computational results highlight a fundamental trade-off between accuracy and numerical efficiency. On the one hand, after an opportune supremizers enrichment, the coupled approach guarantees a faster convergence, despite the need of a larger number of degrees of freedom. On the other hand, the segregated SIMPLE algorithm yields superior reconstruction accuracy, particularly for lower-dimensional reduced spaces, at the cost of a slower convergence rate.

2026-09-07T13:28:22Z Andrea Buffolini Davide Oberto Gianluigi Rozza http://arxiv.org/abs/2608.31042v2 2026-09-07T13:06:17Z

Space-based liquid mirror telescopes (LMTs) have been recently proposed to overcome the scaling limits of traditional rigid mirrors. In these new space architectures, capillary forces would shape a reflective liquid into a spherical optical surface in microgravity. However, the equilibrium, stability, and dynamic behavior of such liquid interfaces under orbital perturbations remain largely uncharacterized. This study investigates the feasibility of space LMTs by combining axisymmetric capillary with thin-film models. Solar radiation pressure and self-gravitation are found to be the dominant perturbations in Sun--Earth L2 orbits, causing equilibrium deformations that exceed the $λ/20$ optical threshold at apertures above 0.86 m for visible ($λ= 380$ nm) and 1.58 m for near-infrared observatories ($λ= 2.5$ $μ$m). Micrometeoroid impacts self-heal within seconds to minutes, settling after filling requires years to decades at large apertures, and propulsive maneuvers breach optical limits within seconds to hours. These results highlight the need for interface control in large-scale systems such as NASA's 50 m Fluidic Telescope (FLUTE). Thermocapillary actuation supports apertures of 2.3/8.0 m (VIS/NIR) at 100 $μ$K and 10.6/37.7 m at 10 $μ$K. Simultaneously, parasitic Marangoni flows impose sub-mK uniformity for NIR and 1--100 $μ$K for visible operation on any capillary LMT. Departing the capillary regime by imposing a surface-normal settling acceleration, ranging from 39 mm s$^{-2}$ (NIR,5 m) to 17 m s$^{-2}$ (VIS,50 m), is the most promising route to tens of meters in aperture. This approach enables a passive implementation effectively suppressing perturbation induced interface distortions and thermal Marangoni flows. Keywords: Liquid mirror telescope, Optics, Space

2026-08-31T16:20:03Z Corrected typo in metadata, article files remain unchanged Janoah Dietrich Álvaro Romero-Calvo http://arxiv.org/abs/2609.07437v1 2026-09-07T12:44:35Z

Physics-informed neural networks (PINNs) represent a growing frontier in using artificial intelligence to solve partial differential equations (PDEs). Automatic differentiation (AD) plays a central role in this paradigm, which is mesh-free and replaces traditional iterative solvers with gradient-based optimization in continuous space. However, the inherent limitations of AD, particularly in handling higher-order derivatives and discontinuous solutions, pose significant challenges for complex problems. This has motivated a growing number of researchers to explore discretization-based constraints as an alternative path. Yet, the respective applicability of these two paradigms remains largely unexplored. In this work, we conduct systematic experiments across a wide spectrum of problems, from simple linear Poisson to high-Mach hypersonic flows with strong discontinuities. Through a rigorous decomposition of approximation, optimization, and truncation errors, we systematically elucidate the fundamental trade-offs and error-governing mechanisms of both paradigms, as well as two representative network architectures: multi-layer perceptron (MLP) and graph neural network (GNN). Our results reveal a consistent trend: as nonlinearity strengthens, the accuracy advantage of discretization-based constraints becomes increasingly pronounced, with smaller optimization errors compensating for the truncation errors. Moreover, the more complex the nonlinearity and boundary conditions, the greater the advantage of GNN over MLP. These insights offer a robust practical guideline for configuring neural PDE solvers in demanding engineering applications. Our source data and code are available at https://github.com/guoxing0809/neuropde_analysis.

2026-09-07T12:44:35Z Xing Guo Hongwei Tang Zewei Meng Yidong Zhang Shaoqiu Xiao Feng Liu http://arxiv.org/abs/2609.07387v1 2026-09-07T12:01:21Z

Heterogeneous exascale systems are reshaping computational fluid dynamics, yet rewriting mature high-order solvers for accelerators can fragment code bases and weaken reproducibility. We present a single-source OpenMP target modernisation of UCNS3D, a high-order unstructured finite-volume solver for compressible flows. The common CPU/GPU implementation preserves its numerical formulation, Fortran code base, and workflows. Rather than porting isolated kernels, we enable the complete explicit time-advancement path: high-order reconstruction, gradient evaluation, inviscid and viscous fluxes, boundary treatment, halo exchange, and solution update. The implementation uses persistent target data regions, flat run-time arrays, compile-time sizing of temporary storage, explicit local algebra, target-callable routines, and GPU-aware MPI with device-resident buffers. These choices address the irregular stencils, complex data structures, and substantial temporary storage of high-order unstructured CFD. Verification using the compressible Taylor-Green vortex shows CPU and GPU dissipation histories agreeing to machine precision on LUMI and with published reference data. A single-node run on the ARCHER2 GPU platform provides an independent portability check. End-to-end performance is evaluated on fully populated nodes using Taylor-Green vortex, LM1021 sonic-boom, and NASA high-lift CRM benchmarks. Relative to the previous production implementation, the refactored CPU path is 1.27-1.67 times faster, while GPU offload delivers same-node speed-ups of 2.71-4.05 and 84-101 percent strong-scaling efficiency. The results show that standards-based OpenMP provides portable, production-scale acceleration without sacrificing numerical fidelity, CPU performance, or software sustainability.

2026-09-07T12:01:21Z Panagiotis Tsoutsanis Michal Uminski Christopher Day David Henty http://arxiv.org/abs/2609.07327v1 2026-09-07T10:43:58Z

In computational fluid dynamics, the numerical simulation of free-surface flows using interface capturing approaches (level set, pseudo-concentration) requires accurate resolution of a transport equation. In the present work, this equation is solved using a new formulation of the Lesaint--Raviart discontinuous Galerkin method, which is particularly suitable for problems without inflow boundaries. The motion is described by the incompressible Navier--Stokes equations with surface tension, discretized using the standard $P2-P1$ Taylor--Hood finite element method in space. Surface tension effects are represented using the so-called Continuum Surface Force model. Finally, the proposed approach is implemented and tested on several benchmarks, including the single rising bubble and the Rayleigh--Taylor instability.

2026-09-07T10:43:58Z W. Herri K. Benmoussa R. Bouydou D. Yakoubi http://arxiv.org/abs/2606.25780v2 2026-09-07T09:19:34Z

The T-shaped mixer is widely used in fundamental studies of chemical engineering. Its transitional regime is well understood, whereas the turbulent dynamics has received scarce attention so far. Here we perform direct numerical simulations of the turbulent regime for Reynolds numbers up to $Re=2000$ at Schmidt number $Sc=1$. Our analysis reveals two distinct stages along the mixing channel prior to relaxation toward duct flow. Near the junction, a jet-like flow forms and exhibits the approximately self-similar behaviour of transitional planar jets. Subsequently, a decay region characterised by power-law decay of turbulent kinetic energy, dissipation and scalar variance emerges. For the velocity field, the observed exponents are consistent with those of decaying turbulence in bounded domains, whereas the scalar-variance exponent is consistent with that of unbounded turbulence. We argue that this apparent discrepancy is a consequence of the mixing process progressing from the center of the channel toward the side walls in the decay region, while turbulence already fills the channel cross-section entirely at the end of the jet region.The time-averaged mixing state presents error-function profiles of the scalar in the transverse direction, similar to the laminar cases, and is quantified here through a stream-wise evolving effective diffusion coefficient.

2026-06-24T12:57:08Z Mohammad Mehdi Zamani Asl Marc Avila http://arxiv.org/abs/2609.07248v1 2026-09-07T09:09:41Z

We employ weakly nonlinear theory to investigate how an externally imposed simple shear flow affects the onset of spontaneous dynamics of an inertialess active filament deforming in Stokes flow. The filament, clamped to a wall at one end, is subjected to a compressive "follower force" applied tangentially at its free end. By extending my earlier weakly nonlinear analysis of the shear-free case (J. Fluid Mech., 1007 A65, 2025), we derive a generalized amplitude equation governing the near-onset dynamics under weak shear. Analysis of the amplitude equation shows that, besides inducing a steady deflection, the shear damps the filament's intrinsic oscillations. This damping arises from a subtle nonlinear resonance between the shear and the intrinsic oscillations, scales quadratically with the shear rate, and is anisotropic---stronger in the flow direction than normal to it. Without shear, stable whirling states, where the filament tip traces a circular orbit in a plane parallel to the wall, and unstable planar-beating states are known to simultaneously emerge at a critical follower-force value, with circular whirling typically observed beyond this threshold. Shear breaks this degeneracy, driving a sequence of dynamical transitions: from circular to elliptical whirling, then to transverse beating (normal to the shear), and ultimately to steady deflection.

2026-09-07T09:09:41Z Ory Schnitzer http://arxiv.org/abs/2609.07232v1 2026-09-07T08:49:29Z

The Volume-of-Fluid implementation in the \href{basilisk.fr}{Basilisk} flow solver is employed to study mass transfer after coalescence-induced jump-off of bubbles on solid substrates at four combinations of bubble radius ($R_m=150$ and 25 $μ$m, hydrogen-water properties) and Schmidt number ($\text{Sc}=210$ and 1). The results show a relatively strong downward entrainment of low-concentration liquid, induced by a rapid movement of the bubble interface at approximately 0.5 to 1 inertio-capillary time units after the moment of coalescence. At $\text{Sc}=210$, this leads to a highly local increase of the Sherwood number at a core region (roughly an area of radius $R_m/2$) below the south pole of the merged bubble, which persists long after the bubble departure due to the slow diffusion at large $\text{Sc}$. The enhancement factor of the Sherwood number is highly dependent on the state of the mass-transfer boundary layer at the moment of coalescence, increasing with smaller boundary layer thicknesses. Shortly after the jump-off, the velocity of the bubble is considerably damped and rapidly approaches its free-rise terminal velocity. The effect of micro-convection on the wall mass transfer coefficient at this stage is insignificant when isolated, similar to what is reported in the literature for purely buoyancy-driven bubble rise -- but slightly stronger.

2026-09-07T08:49:29Z Zahra Saadat Michele Cattani Amin Soltani Pourya Forooghi http://arxiv.org/abs/2609.07073v1 2026-09-07T06:01:57Z

Flapping insect wings generate leading-edge vortices (LEVs) that produce much of the lift required for hovering, yet the frequency governing their formation has not been connected to classical vortex shedding. Roshko scaling for bluff-body wakes, together with the Sigurdson extension to wall-bounded separated flows, identifies a universal vortex-formation Strouhal-number range of approximately 0.15 to 0.17. Here we show that this same range governs LEV formation on both stationary wings and hovering insect wings. We first develop an approximate scaling for stationary flat-plate wings in which discrete LEVs are generated by periodic leading-edge perturbations, and show that maximum lift consistently occurs within the universal Strouhal range. In hovering insects, one LEV forms during each translational half-stroke, allowing the same framework to be applied to published flight data. Despite large differences in morphology, kinematics and Reynolds number, the insect data recover the same Strouhal range. These results reveal a common vortex-formation timescale linking classical separated flows, artificially generated LEVs and the natural LEVs that sustain insect hovering.

2026-09-07T06:01:57Z 4 figures; Supplementary Information included David Greenblatt http://arxiv.org/abs/2609.06992v1 2026-09-07T03:35:13Z

This study proposes a hybrid reduced-order modeling (ROM) framework for the simulation of turbulent flow. The central idea is to decompose flow dynamics according to their temporal characteristics and predict the resulting components individually. The full field is first divided into a sub-field represented by a limited number of proper orthogonal decomposition (POD) modes (named as POD-retained field) and the corresponding residual sub-field (named as POD-truncated field). A frequency-informed POD strategy identifies the retained modes by considering both modal energy and dominant frequency. The evolution of retained POD coefficients, which feature similar temporal scales, is described using a vector autoregressive (VAR) model. In parallel, the POD-truncated field is compressed into a low-dimensional latent space using a Fourier-neural-operator-based Koopman $β$-variational autoencoder (FK-$β$-VAE), with the latent variables subsequently predicted by a switching-VAR model. Turbulent statistics of the full field are recovered by combining the contributions from the two components. The framework is assessed using turbulent channel flow at a friction Reynolds number of $110$. The predicted Reynolds-stress components, turbulent kinetic energy (TKE), and dominant wavenumber spectra show good agreement with the reference. Moreover, in comparison with an alternative framework of full-field modeling (i.e., without field decomposition), the proposed framework yields more accurate and robust long-term statistical predictions.

2026-09-07T03:35:13Z Xianglong Li Zeng Liu Zhan Wang Kai Wang Shunxiang Cao Guangyao Wang http://arxiv.org/abs/2512.21773v2 2026-09-07T02:04:03Z

A semi-implicit, residual-based variational multiscale (VMS) formulation is developed for the incompressible Navier-Stokes equations. The convection term is linearized using an extrapolated (Oseen-type) convecting velocity, producing a linear advection operator whose adjoint can be written exactly. Because of this exact adjoint, unresolved-scale contributions enter the weak form without spatial derivatives of the fine-scale velocity, thereby eliminating the case-by-case adjustments that often accompany nonlinear residual-based VMS implementations. The formulation is presented for a generalized linear convection operator encompassing the convective, skew-symmetric, and divergence forms. Since the discrete method is linear by construction and monolithic for velocity and pressure, each time step requires only one linear solve, reducing wall-clock time by a factor of $2$ to $5$ relative to fully implicit nonlinear formulations while maintaining comparable accuracy. Temporal convergence is verified, and validation is performed on the lid-driven cavity, flow past a cylinder, turbulent channel flow, and flow over a NACA0012 airfoil at a high Reynolds number, demonstrating the efficiency of the proposed approach on problems of practical scale.

2025-12-25T19:46:47Z Biswajit Khara Suresh Murugaiyan Suriya Dhakshinamoorthy Makrand Khanwale Ming-Chen Hsu Baskar Ganapathysubramanian http://arxiv.org/abs/2510.24673v4 2026-09-07T00:22:21Z

Constitutive laws relate fluid stress to deformation and underpin predictions of non-Newtonian behavior in industrial and biological fluids. Standard characterization relies on measurements in idealized flows that often miss physics relevant to complex geometries. Existing data-driven methods overfit sparse data, lack geometry portability, or presuppose constitutive forms. To unify measurement and constitutive discovery, we developed an end-to-end framework that leverages automatic differentiation through a full physics simulation. By embedding a frame-invariant tensor basis neural network (TBNN) within a differentiable non-Newtonian solver, we learn constitutive laws from any flow observable without presupposing a specific model, spanning generalized Newtonian, viscoelastic, and yield-stress behavior. Unlike coordinate-dependent methods, learning local material response enables accurate flow predictions in unseen geometries and conditions without retraining. We then distill the TBNN closure into symbolic form via automated model selection using the Bayesian Information Criterion, extracting interpretable physical parameters. This work establishes a foundation for comprehensive characterization of complex fluids directly within their operating environment ("digital rheometry") with broad applicability to constitutive discovery across engineering and the physical sciences.

2025-10-28T17:38:33Z Alp M. Sunol James V. Roggeveen Mohammed G. Alhashim Henry S. Bae Michael P. Brenner http://arxiv.org/abs/2608.31110v2 2026-09-06T22:39:47Z

Polluted white dwarfs provide a unique window into the composition of exoplanetary material, but interpreting their surface abundances requires a quantitative understanding of the mixing processes in their envelopes. Accretion of metal-rich debris onto hydrogen-rich white dwarfs drives thermohaline (fingering) convection in the underlying radiative zone. Previous studies have modeled this as enhanced diffusive transport, often inferring mass accretion rates, $\dot{M}_{\rm acc}$, that exceed constraints from X-ray observations. Here we develop a time-dependent model that treats thermohaline mixing as a propagating front whose evolution is coupled self-consistently to the surface abundance of heavy elements. We perform hydrodynamical simulations which demonstrate that thermohaline mixing drives the composition gradient towards marginal stability. Using this condition, we derive analytic solutions in shallow and deep stratification regimes, finding that the mixed layer depth, $h$, and surface abundance, $X_{\rm surf}$, both scale as $t^{1/2}$ at early times, transitioning to $h \propto t^{4/27}$ and $X_{\rm surf} \propto t^{10/27}$ at later times. The mixed layer reaches depths of only $\sim 100$ km over $10^5$ yr and, without gravitational settling, never reaches a steady state. Including settling leads to an equilibrium surface abundance scaling as $X_{\rm surf, eq} \propto \dot{M}_{\rm acc}^{30/43}$. Applied to G 29--38, the model matches the observed heavy-element abundance for $\dot{M}_{\rm acc} \sim 2\times 10^9$--$4\times 10^{9}~\mathrm{g~s^{-1}}$, in better agreement with X-ray constraints than prior estimates incorporating thermohaline mixing. We also present a general scaling relation for inferring accretion rates directly from observed surface abundances and stellar properties, giving a practical prescription for other polluted white dwarfs.

2026-08-31T17:14:47Z Submitted to AAS Journals, updated references and label in Fig. 1, more comments welcome! J. R. Fuentes Matias Castro-Tapia Jim Fuller Marcus King