https://arxiv.org/api/9ZmgkyvwXka6/sdFEGEdd2W66LQ 2026-09-10T17:23:14Z 35174 0 15 http://arxiv.org/abs/2609.10497v1 2026-09-09T17:35:11Z

We present a novel reduced-order data assimilation framework, termed Reduced-Order Dynamical Assimilation (RODAS), for reconstructing high-resolution, time-resolved flow fields from sparse velocity measurements. The method combines low-dimensional experimental observations with a physics-based parametric reduced-order model, enabling both spatial extrapolation beyond the measurement region and temporal super-resolution. The approach first identifies the dominant dynamics from sparse measurements through Dynamic Mode Decomposition (DMD), and subsequently reconstructs the corresponding full-order flow evolution by projecting the identified dynamics onto a parametric Proper Orthogonal Decomposition (POD) manifold generated from high-fidelity numerical simulations. Unlike conventional reduced-order data assimilation methods that estimate independent snapshots or treat time as an additional parameter, RODAS reconstructs an entire dynamical trajectory in a single inference step while naturally incorporating parametric variability. We assess the proposed methodology on vortex shedding behind a circular cylinder for both Newtonian and non-Newtonian (Carreau-Yasuda) fluids. Numerical experiments demonstrate accurate reconstruction of high-resolution velocity fields from localized, low-resolution measurements, achieving sub-percent reconstruction errors with sufficiently rich reduced bases, robust performance under severe temporal undersampling, and accurate prediction of engineering quantities of interest such as the drag coefficient. These results demonstrate that RODAS provides an efficient framework for real-time, physics-informed reconstruction of unsteady flows from sparse experimental data.

2026-09-09T17:35:11Z Mauricio Portilla Felipe Galarce Ernesto Castillo Benjamin Herrmann http://arxiv.org/abs/2609.10337v1 2026-09-09T15:34:50Z

Surface active agents (surfactants) are common contaminants found on most air-liquid interfaces. Surfactants lower the surface tension, and hence surfactant concentration gradients generate surface tension gradients, which leads to flow. A canonical surfactant-induced flow is the outward spreading due to the localised deposition of surfactants onto an otherwise clean liquid interface. Eshima et al. (Phys. Rev. Lett., accepted, 2026) demonstrated experimentally and theoretically, through a late-time similarity solution, that surfactant solubility enhances surfactant-induced flows of air-liquid-air sheets and that soluble surfactant solutions can be mapped onto equivalent insoluble surfactant solutions. Here we extend the work theoretically and numerically, developing a systematic framework for the derivation and analysis of such solutions. The relevant nondimensional parameters are quantitatively defined, and the physically accessible parameter space is wide, which our theory and numerical simulations are able to span. We link the solutions for finitely soluble surfactants to the solutions for the limiting regimes of insoluble and infinitely soluble surfactants, where the latter link only holds transiently: the solution of the infinitely soluble limit appears as an intermediate solution that persists ever longer as solubility increases, before the ultimate late-time solution, which maps onto insoluble surfactants, is obtained.

2026-09-09T15:34:50Z Jun Eshima Luc Deike Howard A. Stone http://arxiv.org/abs/2609.10236v1 2026-09-09T14:28:59Z

Atmospheric surface layer flows are computationally challenging, predominantly due to surface roughness and the high Reynolds number, both of which demand exceptionally high spatial resolution in the near-surface region. We have developed a 2-D stochastic-based model for the generation and the streamwise concatenation of instantaneous, step-like velocity profiles featuring key elements of wall turbulent flows, i.e., uniform momentum zones (UMZ) and shear layers (Ehsani et al. 2024a,b), and vortices (Ehsani et al. 2026). The model is extended herein to the top of the logarithmic layer to reproduce the high-Reynolds-number, rough-wall, turbulent boundary layer measured by Saddoughi and Veeravalli(2000), without the support of a UMZ dataset, using only a handful of critical flow parameters: the Taylor microscale λT, the boundary layer height δ, the friction velocity uτ, and the aerodynamic roughness length z0. The primary challenge lies in the integration of the stochastic model with the scaled distributions of the UMZ and vortex characteristics. The resulting statistical moments, energy spectra, and structure functions are compared against the experimental results. The validated code is made available in a GitHub repository.

2026-09-09T14:28:59Z 29 pages, 7 figures Roozbeh Ehsani Michele Guala http://arxiv.org/abs/2606.08405v4 2026-09-09T13:41:14Z

While neural networks excel in autonomous control, their black-box nature makes control decisions difficult to interpret and diagnose in dynamic fluids. Here, we show how self-evolving scientific agents can design explicit, neural-network-free white-box controllers by iteratively interpreting simulation evidence, accumulating control knowledge and refining controller code. We demonstrate this approach on an underactuated two-joint swimmer navigating unsteady flows via joint angular accelerations. Starting from a target-blind propulsive controller, the agent gradually constructs key mechanisms, including travelling-wave propulsion, body-frame guidance, phase-selective steering, redirect bursts and adaptive relief. The resulting controllers reach targets and generalize across changes in target position, wake geometry, cylinder count, and inflow speed without revision. Moreover, 2D control priors transfer successfully to accelerate 3D adaptation. Our work demonstrates that self-evolving agents can autonomously design physically reasoned and generalizable white-box fluid control, showing a promising paradigm beyond traditional reinforcement learning and black-box neural network control.

2026-06-07T01:59:11Z Boai Sun Wenjin Guo Zongmin Yu Liu Yang http://arxiv.org/abs/2609.10165v1 2026-09-09T13:38:54Z

A direct, analytical, non-iterative ghost-cell reconstruction framework is developed for Cartesian-grid embedded-boundary methods. Analytical expressions impose Dirichlet and Neumann boundary conditions directly at the embedded boundary, eliminating intermediate image-point reconstruction, matrix inversion, and precomputation or storage of geometry-dependent reconstruction weights. For the Cartesian stencil considered, dependencies among neighboring ghost cells form a directed acyclic graph. A topological ordering partitions ghost cells into dependency levels, permitting level-by-level reconstruction without iterative updates. The formulation is combined with hybrid ghost cells (HGC), whose centers may lie on either side of the embedded boundary. This placement satisfies the linear reconstruction-stability criterion previously derived for scalar advection while retaining a compact nearest-neighbour Cartesian stencil. An extended-stencil classical ghost-cell formulation (CGC_ES) serves as a stability-preserving reference, distinguishing the effects of reconstruction stability and stencil compactness. The same analytical relations provide solution values and spatial gradients directly on the embedded boundary, enabling evaluation of pressure forces, wall stresses, drag, and lift without separate surface reconstruction or filtering. Simulations of flow past a circular cylinder and an airfoil show that the linear criterion remains a useful indicator of reconstruction stability for the nonlinear incompressible Navier-Stokes cases considered. Classical ghost-cell reconstruction develops spurious oscillations when the criterion is violated, whereas CGC_ES and HGC remain stable. HGC additionally satisfies the stability requirement with a compact nearest-neighbour stencil.

2026-09-09T13:38:54Z Narsimha Reddy Rapaka Pankaj Jagad Yacine Addad Mohamed Kamel Riahi http://arxiv.org/abs/2607.09922v2 2026-09-09T13:09:50Z

A numerical investigation of steady forced convection heat transfer from an isoflux circular cylinder immersed in the liquid metal Galinstan is presented. The governing streamfunction, vorticity, and energy equations are solved using a fourth-order compact finite difference scheme in cylindrical coordinates (FOCS--CC) coupled with a stable pseudo-time iteration (PTI) technique. The influence of the Reynolds number ($1 \leq Re \leq 600$) on the flow and heat transfer characteristics is systematically investigated for Galinstan with a Prandtl number of $Pr=0.025$. The performance and accuracy of the proposed scheme are first established through grid independence studies and validation against previously published numerical results for the average Nusselt number and total drag coefficient over a range of Reynolds numbers. Excellent agreement with the available literature confirms the reliability and robustness of the present formulation. The effects of Reynolds number ($1\leq Re\leq600$) on the flow and thermal fields are examined through streamline patterns, isotherm distributions, and local Nusselt number variations. The results reveal that increasing the Reynolds number promotes flow separation, enlarges the wake region, intensifies downstream thermal transport, and significantly enhances convective heat transfer from the cylinder surface. Furthermore, a new empirical correlation for the average Nusselt number is proposed for Galinstan fluid over the Reynolds number range $1\leq Re\leq600$, exhibiting excellent agreement with the numerical data with a coefficient of determination of $R^2=0.99939$.

2026-07-10T19:17:07Z After further examination, I realized that the manuscript contains fundamental scientific errors. In particular, at (Re=600), the flow is neither steady nor two-dimensional, contrary to the assumptions used. This affects the validity of the results and conclusions. Therefore, I respectfully request withdrawal of the manuscript Dipjyoti Nath http://arxiv.org/abs/2609.10085v1 2026-09-09T12:07:00Z

In this study, we use a constrained Schrödinger--induction system to investigate kinetic-energy fluctuations induced by a fluid singularity. Assuming the cited Navier--Stokes construction with zero initial velocity and its exact exterior profile, we construct a periodic trajectory from a constant normalized wave function and zero connection. The prescribed body force admits a smooth space--time extension across the normalized singular time $t=1$. In this construction, the probability density remains constant and the mean matter kinetic energy stays bounded, whereas the gauge-invariant kinetic-energy variance diverges. We prove a lower growth bound of order $(1-t)^{-1/2-5h}$, with $h$ fixed by the source construction, by integrating the fourth power of the complete velocity's magnitude over an exact exterior region where all oscillatory corrections vanish. After fixing a gauge with constant wave function, we identify a unique weak $L^2$ connection limit outside $L^4$ and construct its positive self-adjoint kinetic operator through the associated magnetic form. We further show that the normalized endpoint state belongs to the form domain but not the operator domain: its first kinetic spectral moment is finite, whereas its second is infinite. These results connect fluid concentration to a loss of kinetic-domain regularity and provide a dynamical benchmark for assessing the limits of mean-energy control in hydrodynamic wave formulations.

2026-09-09T12:07:00Z Weishuo Liu http://arxiv.org/abs/2609.07665v2 2026-09-09T09:42:51Z

The wakes of a lift + cruise aircraft's vertical lift propellers interact with the wing during the transition from hover to forward flight. This study investigates how variations in axial and longitudinal separations between the vertical lift propellers and the wing affect aerodynamic performance during this critical phase. Axial variations were introduced by orienting the motors either upright or inverted at two longitudinal positions relative to the wing. Wind tunnel tests were conducted on the resulting lift + cruise wing configurations over a Reynolds number range of 52,000 to 377,000, using tufts, pressure taps, and load cells to capture aerodynamic behaviour. Results show that the early transition phase (front propeller advance ratios between 0 and 0.25) is particularly sensitive to configuration changes. Rear motor orientation had a pronounced effect: when oriented upright at the shortest longitudinal separation, the active lift propellers increased the lift-drag ratio of the design by approximately 4 units, whereas in the rear motor inverted case the design suffered a 4-point reduction in the lift-drag ratio. Decreasing the longitudinal separation amplified both the beneficial lift contribution of the rear propeller and the generally adverse effects of the front propeller. However, placing the front propeller closer to the wing in the upright orientation enhanced performance at advance ratios between 0.11 and 0.25, due to favourable interactions between the wing and the front propeller's trailing vortices.

2026-09-07T15:51:04Z Oliver Westcott University of Southampton Robert Entwistle University of Southampton Swathi Krishna University of Southampton http://arxiv.org/abs/2609.09773v1 2026-09-09T06:18:58Z

This study investigates the nonlinear kinematics of a premixed slit flame using a two-dimensional $G$-equation level-set framework. Results show that combined forcing induces nonlinear saturation in the FDF, characterized by early gain flattening and premature phase drops, which intensify with the transverse forcing amplitude. Kinematic analysis reveals that this geometric nonlinearity manifests as a reduction in the time-averaged flame height, defined as the mean shift. In the quasi-steady limit, this mean shift is analytically quantified via a multivariate asymptotic expansion, where fourth-order terms successfully capture the saturation mechanism at elevated amplitudes. By introducing a scaling parameter to account for transverse dominance, the frequency-dependent decay of the mean shift in the compact limit collapses onto a single master curve, enabling the derivation of a unified theoretical model that integrates this asymptotic response with a second-order low-pass filter. Furthermore, because the mean shift reduces the physical extent of the flame, it alters the wrinkle propagation time. Correcting the Strouhal number using the measured mean shift collapses the dispersed nonlinear FDF curves onto the linear theory prediction. The analysis is further extended to disturbances convected at a finite speed, for which the linear transfer function is derived analytically and the correction with the measured mean shift continues to collapse the nonlinear FDF. These findings establish that the nonlinear FDF behavior under multidimensional forcing is fundamentally governed by the kinematic mean shift, providing a theoretical baseline for decoupling geometric nonlinearities from other thermo-diffusive or hydrodynamic instabilities in turbulent flames.

2026-09-09T06:18:58Z 16 pages, 16 figures. Accepted for publication in Combustion and Flame Juhoon Son Yong Jea Kim Jungho Sohn Dong-hyuk Shin http://arxiv.org/abs/2603.15038v2 2026-09-09T03:43:46Z

A novel convolutional autoencoder and neural ODE (CAE-NODE) framework is proposed for a reduced-order model (ROM) applied to transient 2D counterflow flames, as an extension of AE-NODE methods in homogeneous reactive systems to spatially resolved flows. The multidimensional thermochemical fields (256 x 256 grid, 21 variables) obtained from direct numerical simulations (DNS) are used in training the CAE, where convolutional layers learned the underlying spatial correlations, allowing the CAE to construct an unsupervised 3D latent manifold that is physically meaningful, smooth, and continuous in time. This results in a compression ratio of over 400,000 times. The NODE then subsequently learns the continuous-time dynamics on the latent manifold, enabling the prediction of the full temporal evolution of the flames by integrating forward in time from an initial condition. The results demonstrate that the CAE-NODE can accurately capture the entire transient process, including ignition, flame propagation, and the gradual transition to a non-premixed condition, with excellent agreement with the DNS, while adhering to conservation principles at virtually no computational cost compared to the reference DNS. Predictions remain accurate at strain rates outside the training range. Moreover, despite being unsupervised, the learned latent manifold is highly correlated with the flame-state descriptors such as the progress variable, mixture fraction, and the scalar dissipation rate. This study, for the first time, highlights the potential of CAE-NODE for surrogate modeling of unsteady dynamics of multi-dimensional reacting flows.

2026-03-16T09:43:49Z Submitted to Combustion and Flame Mert Yakup Baykan Weitao Liu Mohammad Rafi Malik Thorsten Zirwes Andreas Kronenburg Hong G. Im Dong-hyuk Shin http://arxiv.org/abs/2609.09635v1 2026-09-09T02:50:36Z

Externally generated wakes can impinge on porous layers in several practical heat transfer applications. However, the transport of these macroscale vortices and their resulting influence on heat transfer in the porous layer remain unknown. In this paper, two-dimensional pore-resolved simulations are used to examine a square-bluff-body wake impinging on a porous layer composed of an in-line array of heated square obstacles at Re = 500-4000, Pr = 0.7 and 7.0, and porosities $φ$ = 0.75, 0.85, and 0.95. The incident macroscale vortices break down starting immediately at the porous-fluid interface. Following macroscale turbulent thermal transport in this entrance region, fluctuations farther downstream are aligned with the pore geometry and are generated at the microscale level by pore-throat shear, separation, and repeated obstacle wakes. Direct impact locally improves heat transfer at the porous-fluid interface by increasing the local Nusselt number relative to a non-impingement region. The interfacial heat-transfer enhancement varies with porosity, Reynolds number, and Prandtl number, with a peak enhancement of 18.2% observed for $φ$ = 0.85, Pr = 7.0, and Re = 1000. The wake-associated macroscale turbulent heat-flux contribution decays within a consistence entrance region extending approximately 3-4 unit cells into the porous layer across all investigated porosities, Reynolds numbers, and Prandtl numbers. For Re$\ge$1000, the persistent wake momentum deficit subsequently causes the heat-transfer contrast to become negative, resulting in lower heat transfer in the impingement region than in the non-impingement region.

2026-09-09T02:50:36Z Thibaut K. Kemayo Vishal Srikanth Justin Courter Rodrigo R. Caballero Andrey V. Kuznetsov http://arxiv.org/abs/2609.09398v1 2026-09-08T19:52:20Z

Dense granular flows are a common occurrence throughout nature and industry, but still exhibit phenomena that are not fully understood. One of these phenomena is the segregation of particles that constitute a dense granular flow, where particles separate due to differences in properties such as size and density. This work approaches segregation from a new perspective by developing a force model for a single particle based on the observation that there are two opposing drag forces acting on the particle. Validation of the model in mono-disperse flows reveals a family of velocity profiles, including a Bagnold profile. Further validation is done by comparing with known particle scaling laws in literature. The force model shows that the mechanism of segregation is always present in dense granular flows and that mono-disperse flows are a unique case where it is not distinctly visible. The insights in this paper prove a fundamental new way of thinking about dense granular flows and its individual particles, opening the field for new research directions.

2026-09-08T19:52:20Z M. P. van Schrojenstein Lantman http://arxiv.org/abs/2609.09341v1 2026-09-08T18:25:04Z

We investigate turbulent boundary layers at Mach 2.5 over sinusoidal roughness at matched $Re_τ=784$. We considered three wall temperatures, $T_w/T_r=$ 1.0, 0.7, and 0.4. Each wall temperature was repeated with a smooth and rough surface, the latter following a three-dimensional sinusoidal profile with effective slope 0.5 and matched $k^+=79.1$. In total six direct numerical simulations were completed. Analysis of mean wall shear and heat transfer detailed the augmentation in skin friction and heat transfer coefficient between smooth and rough cases; resulting in the classical failure of the Reynolds analogy for rough walls. We also show that differences in shear stress across wall temperatures are driven by the viscous component even though the pressure component dominates. The roughness sublayer was found to be $R_{RSL}=3k-6k$, consistent with the literature. Moreover, the wall offset $d=d_Θ\approx0.5k$ for both momentum and thermal boundary layers, signifying the offset represents the half peak-to-valley height rather than the "mean roughness height." For the mean momentum boundary layer, we find the present conditions recover the incompressible roughness function $Δu_1^+$ when matched via the semi-local roughness Reynolds number $k^*$. For this reason, an equivalent sand-grain roughness of $k_s^*\approx3.7k^*$ is proposed. The existing compressible transformations hold regardless of wall temperature or roughness - contradicting recent claims otherwise. The generalized Reynolds analogy works for smooth walls but fails for rough walls; a roughness correction term is proposed and validated. Compressible mean temperature transformations fail for cold walls, especially when $(T_w-T_e)/(T_r-T_e)<0$. The thermal roughness function, $ΔΘ^+$, is reported with caution given transformation singularities.

2026-09-08T18:25:04Z Mateus A. R. Braga Robyn L. Macdonald http://arxiv.org/abs/2609.09024v1 2026-09-08T16:53:27Z

In aquatic environments, gradients in flow velocity and turbulence define a constantly shifting landscape that sets the physical constraints on propulsion and energy expenditure in fish. Successfully navigating these complex flows depends on the ability to sense and respond to subtle hydrodynamic cues in an energy-efficient manner. Revealing these mechanisms is central to understanding how fish identify and exploit favorable flow conditions. To this end, we designed a hydrodynamic maze with spatially varying mean flow and turbulence, creating a controlled heterogeneous flow landscape for understanding fish movement strategies. We found that fish escape energetically unfavorable regions by yawing their bodies relative to the flow. These yawed orientations appear to facilitate lateral migration through lift forces and may improve sensitivity to local flow variations. Notably, fish maintain body orientations near, but below, predicted stall conditions to exploit lift without a significant increase in drag. These findings provide insight into how fish navigate heterogeneous hydrodynamic environments, with potential relevance for both natural and engineered flow systems.

2026-09-08T16:53:27Z Proc. Natl. Acad. Sci. U.S.A. 123 (36) e2613565123 Michael A. Calicchia Rui Ni 10.1073/pnas.2613565123 http://arxiv.org/abs/2608.18323v2 2026-09-08T16:36:07Z

Predicting flow-induced sound from moving and deforming bodies is computationally demanding because the near-field hydrodynamics and the far-field acoustics require substantially different spatial resolutions and domain extents. A fully parallel hybrid framework is developed to address this disparity by coupling an incompressible Navier-Stokes solver to an acoustic perturbation equation (APE) solver on independently generated, non-conforming Cartesian grids. A sharp-interface ghost-cell immersed boundary method, with radial-basis-function reconstruction, imposes the boundary conditions for complex moving geometries on both grids. The converged flow field supplies the acoustic source through a one-way, precomputed parallel interpolation operator. This arrangement confines the flow grid to the body and wake while allowing the acoustic grid to extend independently into the far field. The framework is validated for Gaussian-pulse propagation, pulse scattering by a rigid cylinder, tonal sound from flow past a cylinder, and radiation from a traveling wavy foil. The predicted waveforms, wavelengths, pressure amplitudes, and radiation patterns agree closely with analytical solutions and published reference data. Applications to eel and Jack fish locomotion, a four-eel school, a manta ray, and a harbor seal further demonstrate the treatment of realistic three-dimensional morphologies, large boundary deformation, and multiple interacting swimmers. The results resolve morphology-dependent acoustic signatures and interference-driven changes in far-field directivity without requiring the flow grid to span the acoustic far field.

2026-08-18T21:15:59Z Amirhossein Fardi Muhammad Saif Ullah Khalid