Building a Start-to-End Model of the CESR Injector Linac

2026-08-05T17:32:32Z

The CESR injector linac supplies positrons to the Cornell Electron Storage Ring in six stages: a thermionic cathode, a 150 kV DC gun, a prebuncher, four electron linac sections, a tungsten positron converter, and four positron linacs. We present a start-to-end model of the full chain, built in Python from open-source codes. WarpX is used for the space-charge-dominated cathode, gun, prebuncher, and electron linacs, Geant4 for positron production, and Impact-T for the positron linacs. The beam reaches the converter at 146 MeV and the recaptured positrons are accelerated to 250 MeV. Stage configurations are written in YAML to allow algorithmic adjustment by Xopt for ML optimization.

Laser-Plasma Accelerator Beams in Light Sources: Femtosecond High-Brightness Radiation through Chirped Pulse Injection

2026-08-05T11:07:38Z

We propose a chirped-pulse injection scheme into a hard x-ray low-emittance synchrotron light source such as PETRA IV from a laser-plasma electron injector with active energy compression. The scheme enables delivering kA-scale short pulses with several tens of hertz repetition rate to any synchrotron beamline in the ring and allows producing femtosecond temporally coherent radiation pulses at target beamlines.

Accessing the symmetric component of quadrupole misalignment through counter-rotating closed orbits in EDM storage rings

2026-08-05T10:06:21Z

In the storage ring proposed to measure the proton electric dipole moment (EDM), quadrupole misalignments of a few microns mimic a genuine EDM through a geometric (Berry) phase; at a 10 micron rms misalignment the false signal is up to a thousand times the target sensitivity of 1e-29 e-cm. The misalignment splits into an antisymmetric component, which distorts the closed orbit and is visible to the beam-position monitors, and a symmetric component, whose orbit signature is strongly suppressed. Standard single-beam orbit correction therefore removes only the antisymmetric part. The proposed design reaches the symmetric one by beam-based alignment (BBA), which is effective but relatively slow and invasive. Using symplectic beam and spin tracking, we show that correcting the two counter-rotating beams jointly recovers the symmetric component from the orbit itself; it is carried by the sum of the two orbits, whereas their difference is blind and a single beam is far too weak to recover it. The static BPM offset is degenerate with the symmetric misalignment in this sum, so the scheme does not replace the initial absolute alignment. However, the drift is differential and the offset cancels, so continuous two-beam correction maintains the alignment after a single initial BBA calibration, reducing the repeated realignment required by the original proton EDM proposal.

On the relationship between the gain of Stimulated Raman Backscatter of a short-pulse laser in a plasma and the Pierce parameter for XFELs

2026-08-05T06:50:30Z

It is shown that the convective gain of Stimulated Raman Backscatter (SRBS) within a single laser wavelength in the strongly coupled regime is equivalent to the Pierce parameter commonly used to describe high gain x-ray Free Electron Lasers (XFELs). The comparison utilizes the fact that the gain is a Lorentz invariant so the Pierce parameter is written in terms of the FEL parameters in the electron beam's rest frame. It is thus inferred that there is a direct correspondence of the physics between SRBS in the strong-coupled regime and high gain XFELs in the Compton regime.

Generation of dense relativistic electron beams via vortex laser-driven self-generated magnetic pinching

2026-08-04T07:12:07Z

In multi-petawatt laser plasma accelerators, achieving high-density relativistic electron beams is typically accompanied by large transverse divergence, limiting the attainable effective electron density needed for high-flux interaction regimes relevant to laboratory astrophysics. Here we report experimental demonstration of self-generated magnetic pinching (SMP), a collective mechanism that actively regulates transverse beam dynamics using a Laguerre-Gaussian laser at strong relativistic intensity (~8 x 10^19 W/cm^2) interacting with an underdense plasma. The electron beam evolves from a two-lobe high-charge injection structure into a compressed, high-density profile, yielding a threefold reduction in divergence and nearly an order-of-magnitude enhancement in effective beam density compared with a Gaussian driver. Particle-in-cell simulations agree with the experimental observations and reveal that a self-generated azimuthal magnetic field governs the electron dynamics within the SMP regime, which is defined by the forming condition S = 0.717 l a0 [ne(10^18 cm^-3)]^-3/4 = 1, where l, a0, and ne are topological charge, laser amplitude, and plasma density, respectively. A transient kick from a dense inner sheath electron population drives collective magnetic pinching, transforming an initially separated electron distribution into a compressed and well-collimated beam. For higher-power laser systems, the forming condition can be extended to higher plasma densities and larger orbital angular momentum modes, potentially enabling electron beams with charges exceeding several nC and effective densities above 10^19 cm^-3. This mechanism provides a route to overcoming transverse expansion and enhancing rare interaction processes relevant to high-flux particle sources.

Impact of QED backgrounds on light-by-light scattering measurements at $e^+e^-$ and $e^-e^-$ colliders

2026-08-04T05:36:42Z

The process of elastic scattering of photons ($γγ\to γγ$, light-by-light scattering) has attracted significant interest in recent years as a loop-induced process sensitive to all charged particles. To date, this process has been studied through Delbrück scattering, photon splitting in the nuclear Coulomb field, and ultra-peripheral heavy-ion collisions at the LHC. Future precision measurements are anticipated at high-luminosity $e^+e^-$ colliders (SuperKEKb, FCC, CEPC, ILC, CLIC), their $e^-e^-$ options, and $γγ$ colliders based on the backscattering of laser photons. In this paper, we show that background QED processes severely limit the study of elastic light-by-light scattering at $e^+e^-$ colliders. For the $e^+e^-$ case, the main background arises from $e^+e^-$ annihilation into two photons within the detector acceptance after the initial electron and positron emit hard ISR photons at small angles. Since only two photons with a small total transverse momentum are registered in the detector in both cases, this process effectively mimics the $γγ\to γγ$ signal with a significantly larger cross section at high invariant masses. Other relevant background QED processes for both types of collisions are also comprehensively analyzed and discussed.

A diagnostic system of 5.7 keV muon beam for muon accelerator

2026-08-03T16:33:37Z

Realization of a low-emittance muon beam through the acceleration of keV-scale muons requires the injection of a suitably matched beam into an accelerator, since beam mismatch can lead to emittance growth and reduced acceleration efficiency. In one such scheme, muons are first thermalized to room temperature and then injected into a linear accelerator. Non-destructive diagnostics are challenging because of the low energy and low intensity. We developed a compact low-energy muon diagnostic system compatible with the accelerator under construction at J-PARC. The system is designed to evaluate beam conditions required for precise tuning prior to acceleration. Commissioning with low-energy muon sources shows the system's capability to identify low-energy muon signals and measure beam profiles.

The Ponderomotive Effects of Narrow-band, Superconducting Resonators in Open and Closed Loop

2026-08-03T14:13:53Z

In this work, we present measurements of ponderomotive instabilities in narrow-band, coaxial resonators in open and closed control loop systems. We show an analytical scheme we will use in future studies to examine the dependency of open loop stability on mechanical parameters. Analytical and simulation models are used to predict the onset of the oscillatory instability in half wave resonators with active disturbance rejection control for amplitude and phase stabilization. We demonstrate that for high amplitude controller bandwidths, ponderomotive oscillations can couple with the controller frequency response via higher harmonics and lower the threshold for the oscillatory instability. We reaffirm the superiority of in-phase/quadrature $(I/Q)$ component control in regards to preventing the oscillatory instability, and show how the phase controller can amplify the crosstalk of disturbances in amplitude and phase control. In cases with large disturbances, this effect can lead to instabilities not present in $I/Q$ control.

Beam energy measurement at the European XFEL with high-performance trajectory fitting

2026-08-03T13:57:44Z

This contribution presents the method used for beam energy monitoring at the European XFEL. It relies on high-performance trajectory fitting of beam position monitor data against an online model of the accelerator lattice. Unlike most other methods, it can be applied to virtually any section of the lattice with sufficient dispersion without the need for manual adaptation. Our implementation is fast enough to measure the energy of many thousands of bunches per second in realtime on conventional x86 hardware shared with other processes. A short outline of the technique is presented and illustrated with data from the accelerator.

Mass Spectrometry Studies of Hydrogen Ions Energy Distributions in an ECR- based Large Volume Plasma Source

2026-08-03T13:44:39Z

Plasma is produced in a Large Volume Plasma Source (LVPS; dia. = 1 m, height = 1m) using CW microwaves (= 400 - 600 W, 2.45 GHz), in a compact ECR plasma source (CEPS) attached to LVPS, at hydrogen gas pressures = 1 - 3 mTorr. Plasma expands along the CEPS magnetic field into LVPS. A Hiden Analytical HPR 60 molecular beam mass spectrometer (MBMS) is used to measure the H^- ion energy distribution functions (IEDFs) in the downstream plasma. Previous plasma characterization studies in LVPS indicated favourable downstream plasma conditions for volume production of H^- ions. Measurements conducted with the MBMS probe aligned facing the plasma flow = 80 cm downstream, gave typical H^- count rates = 3 x 10^5 counts /s, at = 400 W, = 1 mTorr, along with a distinct high energy tail (<= 20 eV). These and other results are analyzed in detail. The positive ion spectrum showed the H_3^+ count to be consistently high in all cases (= 60-70 %); the counts for H_2^+ and H^+ were =30-35 % and a =few %. Combining the Langmuir probe (LP) and MBMS data it is possible to determine the approximate densities in front of the MBMS probe aperture. At = 500 W and = 2 mTorr, one finds: n_(H^+) = 9.6 x 10^9 cm^(-3), n_(H_2^+) = 1.7 x 10^10 cm^(-3) and n_(H_3^+) = 4.3 x 10^10 cm^(-3). The corresponding H^- density, = 80 cm downstream is n_(H^-) = 3.9 x 10^8 cm^(-3). Accounting for all H^- losses due to scattering and destruction, one finds the effective mean free path for H^- loss to be = 12.4 cm. Noting that H^- formation takes place about = 10 - 30 cm downstream of the source exit, the approximate average H^- density in the formation zone is determined as = 5.5 x 10^10 cm^(-3). This value is remarkably encouraging for H^- production in volume mode, considering the large chamber volume and area, as well as the very moderate power used for the experiments.

Transverse coupled-bunch instabilities driven by high-order modes near the coupling resonance

2026-08-03T09:15:46Z

Betatron coupling near the difference resonance has been explored and adopted in several fourth-generation storage rings, yet its influence on high-order-mode-driven transverse coupled-bunch instabilities has not been systematically established. Using the Hefei Advanced Light Facility (HALF) as an example, we investigate this effect through theoretical analysis and macroparticle tracking simulations. The theoretical predictions agree well with macroparticle tracking simulations in both the weak- and strong-instability regimes, validating the description over the parameter ranges considered. For the vertical HOMs studied with HALF parameters, suitable betatron coupling effectively suppresses the instability, offering potential benefits for transverse stability control.

Machine Learning Optimization of E-Beam Transport for a Superradiant FEL

2026-08-03T08:21:04Z

We present an optimization procedure using machine learning (ML) libraries for optimization of electron beam transport for maximal bunch compression and optimal operation of a bunched-beam Superradiant FEL. This is exemplified for the parameters of the 6MeV ORGAD Accelerator at Ariel University that is driving a THz Superradiant waveguide FEL. For superradiant emission (proportionally to the number of electrons squared), the bunch duration $σ_t$ at the undulator should be shorter than the optical period (2$π/ω$) of the radiation. Also, the beam transport optimization must confine the transverse dimensions of the beam to enter the undulator waveguide. The variables of the ML Bayesian optimization are the RF parameters and the currents of the coils and quads along the beamline. The beam dimensions and duration are provided from full 3D GPT simulations that are automatically driven by the ML exploration and exploitation algorithms. Twenty-five simulation iterations sufficed to arrive to an optimal beam transport design.

Generation of Ultrabrilliant Positron Beam via Superponderomotive Injection in Laser Wakefield Acceleration

2026-08-01T11:48:02Z

Plasma-based acceleration of positrons attracts extensive interest owing to the ultrahigh accelerating gradient and ultrashort duration, while generating wakefield positron beam by the inherent injection is still a great challenge. Here, we put forward a superponderomotive injection method of positrons in the blowout regime of laser wakefield acceleration. The dephasing-rate integral equation reveals a twofold mechanism: the longitudinal laser field delays phase-locking, guiding positrons into the paraxial focusing region, while the transverse laser Lorentz force suppresses the dephasing rate below unity, trapping them into the laser-modulated wakefield. Particle-in-cell (PIC) simulations demonstrate this via a donut-wake--pair-jet collision, generating low-emittance ($\sim$0.05~mm~mrad) multicycle positron beams. Start-to-end simulations for post-acceleration in the second-stage donut wakefield confirm high-throughput injection-to-acceleration coupling, yielding quasi-monoenergetic beam with six-dimensional brightness $\sim 10^{15}~\rm{A/m^2}/0.1\%$. This plasma-based injection-acceleration scheme opens a novel compact route to ultrabrilliant positron sources for ultrafast material diagnostics, laboratory astrophysics, and next-generation electron--positron colliders.

Generation of period-tunable MeV few-attosecond electron pulse trains via counter-propagating lasers

2026-08-01T10:11:14Z

Attosecond electron pulses permit real-time probing of ultrafast material dynamics. However, generating few-attosecond electron pulses with MeV energies and low energy spread remains an enduring challenge for conventional beam-modulation techniques. Here we propose a compact dual-laser scheme to modulate readily accessible electron beams into few-attosecond pulse trains, leveraging a stable parametric-resonance regime coupled with direct laser acceleration. An accompanying theoretical framework is developed, yielding closed-form expressions for the tunable pulse period, duration, energy modulation and formation time, enabling flexible customization of the produced attosecond pulse trains. Consistent with these theoretical predictions, simulations verify the generation of ~ 1 as pulses with a Lorentz factor up to 15 and a relative energy spread below 0.02%. This work offers an experimentally feasible pathway toward high-quality, tunable MeV few-attosecond electron pulses.

Automating the analysis of micron-scale synchrotron diffraction data on inhomogeneous polycrystalline samples: a solid oxide electrolysis cell case study

2026-07-30T21:56:22Z

A novel approach to post mortem characterisation of electrochemical and photovoltaic devices is spatially-resolved diffraction using a hyper-focused, micron-width x-ray beam to examine the distribution of degradation products and strain, a technique called $μ$-XRD. Aside from the experimental difficulties associated with beam focusing and sample preparation, which are themselves non-trivial, the analysis of resulting data is complex and challenging, with full Rietveld analysis rarely attempted in literature. The difficulty lies in the size of the data, which may consist of hundreds or even thousands of diffraction patterns with very different crystallographic phase compositions depending on position within the device, and the difficulty in fitting the data due to the presence of many phases at the same position, including possible degradation products which may be difficult to index and assign to known phases. In this paper, we present a fully-automated open access Python routine for performing phase identification and Rietveld analysis on 2D datasets of diffraction pattern taken at micron-scale positions, measured over the cross-section of a chemically inhomogeneous device with polycrystalline phases. Solid oxide electrolyser cells are a promising technology for green hydrogen production which can utilise waste heat to split water at higher efficiencies than low-temperature electrolysis techniques such as polymer electrolyte membranes, but exhibit many degradation modes due to the high operating temperatures. We present a case study using our analysis protocol on an SOEC fragment encompassing the air electrode, cation diffusion barrier, electrolyte, and fuel electrode. With modification, this protocol could be applied to other devices such as all-solid-state batteries, wet-electrolyte battery electrodes, solid oxide fuel cells, photovoltaic devices, and metal-oxide pseudocapacitors.