https://arxiv.org/api/OpHJ+bjxlWGaiYvHU7tQIOARu78 2026-04-21T10:16:10Z 8758 720 15 http://arxiv.org/abs/2503.22053v1 2025-03-28T00:14:16Z

This study investigates the autoresonant acceleration of electrons using the GYRAC mechanism in a cylindrical cavity excited in the TE$_{011}$ microwave mode, under a slowly increasing external magnetic field. The acceleration process is driven by the interaction between electrons and the right-hand circularly polarized (RHP) component of the electric field, maintained in phase through electron cyclotron resonance (ECR). A simplified single-particle model and numerical simulations based on the relativistic Newton-Lorentz equation were employed to evaluate particle dynamics under different values of the magnetic field growth parameter $ α$. The results demonstrate that efficient trapping and energy transfer can be achieved for appropriate values of $ α$, and that the spatial non-uniformity of the TE$_{011}$ mode introduces critical sensitivity to initial particle positioning. The study further identifies a ring-shaped region in which electrons are consistently captured in the GYRAC regime, and shows how the evolution of the Larmor radius, phase shift, and energy distribution depends on the electromagnetic configuration. Simulations involving disk-like and ring-like electron clouds reveal the fraction of captured, escaped, and uncaptured particles, confirming that precise control of the magnetic field variation is essential to optimize the efficiency of the acceleration process. These findings provide a basis for future self-consistent plasma simulations and support the development of compact radiation sources based on GYRAC-TE$_{011}$ acceleration.

2025-03-28T00:14:16Z Oswaldo Otero Jesús E. López P. Tsygankov Carlos J. Páez-González E. A. Orozco http://arxiv.org/abs/2502.13817v2 2025-03-27T23:11:28Z

Metallic carbon nanotubes (CNTs) can provide ultra-dense, homogeneous plasma capable of sustaining resonant plasma waves-known as plasmons-with ultra-high field amplitudes. These waves can be efficiently driven by either high-intensity laser pulses or high-density relativistic charged particle beams. In this study, we use numerical simulations to propose that electrons and positrons can be accelerated in wakefields generated by the leaky electromagnetic field of surface plasmons. These plasmons are excited when a high-intensity optical laser pulse propagates paraxially through a cylindrical vacuum channel structured within a CNT forest. The wakefield is stably sustained by a non-evanescent longitudinal field with $\si{TV/m}$-level amplitudes. This mechanism differs significantly from the plasma wakefield generation in uniform gaseous plasmas. Traveling at the speed of light in vacuum, with phase-matched focusing fields, the wakefield acceleration is highly efficient for both electron and positron beams. We also examine two potential electron injection mechanisms: edge injection and self-injection. Both mechanisms are feasible with current laser facilities, paving the way for experimental realization. Beyond presenting a promising pathway toward ultra-compact, high-energy solid-state plasma particle accelerators, this work also expands the potential of high-energy plasmonics.

2025-02-19T15:31:11Z Bifeng Lei Hao Zhang Cristian Bontoiu Alexandre Bonatto Pablo Martin-Luna Bin Liu Javier Resta-Lopez Guoxing Xia Carsten Welsch 10.1088/1361-6587/ade00a http://arxiv.org/abs/2503.21669v1 2025-03-27T16:36:33Z

We discuss the main elements of a collider facility based on proton-driven plasma wakefield acceleration. We show that very competitive luminosities could be reached for high energy $e^+e^-$ colliders. A first set of parameters was developed for a Higgs Factory indicating that such a scheme is indeed potentially feasible. There are clearly many challenges to the development of this scheme, including novel RF acceleration modules and high precision and strong magnets for the proton driver. Challenges in the plasma acceleration stage include the ability to accelerate positrons while maintaining necessary emittance and the energy transfer efficiency from the driver to the witness. Since many exciting applications would become available from our approach, its development should be pursued.

2025-03-27T16:36:33Z Input to the EPPSU Allen Caldwell John Farmer Nelson Lopes Alexander Pukhov Ferdinand Willeke Thomas Wilson http://arxiv.org/abs/2405.05652v2 2025-03-27T06:29:04Z

In this article, we consider two dynamical systems: the McMillan sextupole and octupole integrable mappings, originally proposed by Edwin McMillan. Both represent the simplest symmetric McMillan maps, characterized by a single intrinsic parameter. While these systems find numerous applications across various domains of mathematics and physics, some of their dynamical properties remain unexplored. We aim to bridge this gap by providing a comprehensive description of all stable trajectories, including the parametrization of invariant curves, Poincaré rotation numbers, and canonical action-angle variables. In the second part, we establish connections between these maps and general chaotic maps in standard form. Our investigation reveals that the McMillan sextupole and octupole serve as first-order approximations of the dynamics around the fixed point, akin to the linear map and quadratic invariant (known as the Courant-Snyder invariant in accelerator physics), which represents zeroth-order approximations (referred to as linearization). Furthermore, we propose a novel formalism for nonlinear Twiss parameters, which accounts for the dependence of rotation number on amplitude. This stands in contrast to conventional betatron phase advance used in accelerator physics, which remains independent of amplitude. Notably, in the context of accelerator physics, this new formalism demonstrates its capability in predicting dynamical aperture around low-order resonances for flat beams, a critical aspect in beam injection/extraction scenarios.

2024-05-09T09:58:31Z Physica D: Nonlinear Phenomena Volume 476, June 2025, 134620 Tim Zolkin Sergei Nagaitsev Ivan Morozov 10.1016/j.physd.2025.134620 http://arxiv.org/abs/2501.11072v3 2025-03-25T18:20:42Z

The HALHF collaboration has discussed a new baseline for the project, taking into account comments from the accelerator community on various aspects of the original design. In particular, these concerned the practicality of the dual-purpose linac to accelerate both colliding positron bunches and the drive beams required for the plasma linac. In addition, many other aspects of the project were also considered; the discussion and conclusions are documented in this paper. Finally, a new baseline is outlined that has been optimised and addresses several weaknesses in the original design, has higher luminosity, reduced centre-of-mass energy boost and additional features such as positron polarization as well as electron polarization. Although HALHF has become longer and more expensive, it remains significantly smaller and cheaper than other mature Higgs factory designs currently under discussion.

2025-01-19T15:17:48Z 32 pages, 13 figures, 2 tables Brian Foster Erik Adli Timothy L. Barklow Mikael Berggren Stewart Boogert Jian Bin Ben Chen Richard D'Arcy Pierre Drobniak Sinead Farrington Spencer Gessner Mark J. Hogan Daniel Kalvik Antoine Laudrain Carl A. Lindstrøm Benno List Jenny List Xueying Lu Gudrid Moortgat Pick Kristjan Põder Andrei Seryi Kyrre Sjobak Maxence Thèvenet Nicholas J. Walker Jonathan Wood http://arxiv.org/abs/2503.19122v1 2025-03-24T20:18:12Z

Particle tracking codes are one of the fundamental tools used in the design and the study of complex magnetic lattices in accelerator physics. For most practical applications, non-linear lenses are included and the Courant-Snyder formalism falls short of a complete description of the motion. Likewise, when the longitudinal motion is added, synchro-betatron coupling complicates the dynamics and different formalisms are typically needed to explain the motion. In this paper, a revised formalism is proposed based on the Fourier expansion of the trajectory -- known to be foundational in the KAM theorem -- which naturally describes non-linear motion in 2D, 4D and 6D. After extracting the fundamental frequencies and the Fourier coefficients from tracking data, it is shown that an approximate energy manifold (an invariant torus) can be constructed from the single-particle motion. This cornerstone allows to visualize and compute the areas of the torus projections in all conjugate planes, conserved under symplectic transformations. These are the integrals of motion, ultimately expressed in terms of the Fourier coefficients. As a numerical demonstration of this formalism, the case of the 6-dimensional Large Hadron Collider (LHC) is studied. Examples from the 2D and 4D Hénon map are also provided. Even for heavily smeared and intricate non-linear motion, it is shown that invariant tori accurately describe the motion of single particles for a large region of the phase space, as suggested by the KAM theorem.

2025-03-24T20:18:12Z Philippe Belanger Guido Sterbini http://arxiv.org/abs/2503.18843v1 2025-03-24T16:16:39Z

Vortex $γ$ photons carrying orbital angular momenta (OAM) hold great potential for various applications. However, their generation remains a great challenge. Here, we successfully generate sub-MeV vortex $γ$ photons via all-optical inverse Compton scattering of relativistic electrons colliding with a sub-relativistic Laguerre-Gaussian laser. In principle, directly measuring the OAM of $γ$ photons is challenging due to their incoherence and extremely short wavelength. Therein, we put forward a novel method to determine the OAM properties by revealing the quantum opening angle of vortex $γ$ photons, since vortex particles exhibit not only a spiral phase but also transverse momentum according to the quantum electrodynamics theory. Thus,$γ$ photons carrying OAM anifest a much larger angular distribution than those without OAM, which has been clearly observed in our experiments. This angular expansion is considered as an overall effect lying beyond classical theory. Our method provides the first experimental evidence for detecting vortex $γ$ photons and opens a new perspective for investigating OAM-induced quantum phenomena in broad fields.

2025-03-24T16:16:39Z 8 pages, 4 figures Mingxuan Wei Siyu Chen Yu Wang Xichen Hu Mingyang Zhu Hao Hu Pei-Lun He Weijun Zhou Jiao Jia Li Lu Boyuan Li Feng Liu Min Chen Liming Chen Jian-Xing Li Wenchao Yan Jie Zhang http://arxiv.org/abs/2405.10573v3 2025-03-22T14:43:49Z

The pursuit of coherent radiation generation remains a key direction in the advancement of storage ring light sources. Despite the potential of laser modulation in achieving this goal, it leads to a significant decline in the quality of the electron beam. Efforts to mitigate this decline have resulted in the proposal of demodulation schemes. However, implementing modulation and demodulation within the storage ring presents significant challenges due to dynamical and spatial constraints within straight sections. In this study, we propose a straightforward and easily implementable method for achieving reversible laser modulation in a storage ring. Notably, our approach circumvents the need for special storage ring requirements, such as lengthy straight sections or bypass section. Simulation results demonstrate a substantial restoration of beam quality following demodulation. This innovative scheme holds great promise for the realization of high repetition rate coherent storage ring light sources.

2024-05-17T06:57:27Z 12 pages, 9 figures Weihang Liu Yu Zhao Yi Jiao Xiao Li Sheng Wang Chao Feng http://arxiv.org/abs/2503.22806v1 2025-03-21T19:31:42Z

The joint expertise of ANL and FNAL has led to the production of Nb3Sn undulator magnets in operation in the ANL Advanced Photon Source (APS). These magnets showed performance reproducibility close to the short sample limit, and a design field increase of 20% at 820A. However, the long training did not allow obtaining the expected 50% increase of the on-axis magnetic field with respect to the ~1 T produced at 450 A current in the ANL NbTi undulator. To address this, 10-pole long undulator prototypes were fabricated, and CTD-101K was replaced as impregnation material with TELENE, an organic olefin-based thermosetting dicyclopentadiene resin produced by RIMTEC Corporation, Japan. Training and magnet retraining after a thermal cycle were nearly eliminated, with only a couple of quenches needed before reaching short sample limit at over 1,100 A. TELENE will enable operation of Nb3Sn undulators much closer to their short sample limit, expanding the energy range and brightness intensity of light sources. TELENE is Co-60 gamma radiation resistant up to 7-8 MGy, and therefore already applicable to impregnate planar, helical and universal devices operating in lower radiation environments than high energy colliders.

2025-03-21T19:31:42Z ASC 2024 IEEE Trans.Appl.Supercond. 2025 Emanuela Barzi Masaki Takeuchi Daniele Turrioni Akihiro Kikuchi 10.1109/TASC.2025.3540817 http://arxiv.org/abs/2503.17360v1 2025-03-21T17:59:23Z

Vacuum breakdown in accelerator structures is a critical challenge that occurs under high electric fields. In environments subjected to hydrogen ion irradiation or high beam losses, such as in Radio-Frequency Quadrupoles (RFQ), residual hydrocarbons from the vacuum may result in carbon contamination of the metal surfaces from charged particle induced cracking. Under these conditions, it has been assessed that surface carbon contamination leads to a decrement of the surface electric field holding properties. This study extends the latest research by exploring the efficacy of Oxygen Plasma Cleaning (OPC) on metal electrodes irradiated by low energy hydrogen ion beam with the purpose of reducing surface carbon contamination. OPC treatment has been employed on different metals, namely copper beryllium (CuBe2), oxygen-free copper (Cu-OFE), and stainless steel (SS316LN). Treated electrodes have been tested for electric field performance in a DC pulsed system and results compared with non-irradiated electrodes and irradiated ones without OPC treatment. The study indicates a significant reduction in carbon contamination by OPC, enough to allow irradiated materials to achieve performances comparable with the electric field strength of raw surfaces. Moreover, it has been observed that stainless steel samples had some alteration in the surface chemistry that enhanced the materials ability to sustain high electric fields while decreasing vacuum arcing events. Notably, OPC treated SS316LN electrodes surpassed the performance value of untreated ones, demonstrating the potential of plasma treatments in extending the operational performance of accelerator components.

2025-03-21T17:59:23Z Submitted to Physical Review Accelerators and Beams, 17/03/2025 C. Serafim S. Calatroni F. Djurabekova M. C. Giordano M. Himmerlich V. Bjelland C. Kouzios P. Costa Pinto A. T. Perez-Fontenla W. Wuensch A. Grudiev S. Sgobba http://arxiv.org/abs/2503.17081v1 2025-03-21T12:10:55Z

The FCC program at CERN provides an attractive all-in-one solution to address many of the key questions in particle physics. While we fully support the efforts towards this ambitious path, we believe that it is important to prepare a mitigation strategy in case the program faces unexpected obstacles for geopolitical or other reasons. This approach could be based on two components: I) a circular electron-positron collider in the LHC tunnel that operates at the Z-pole energy of 45.6 GeV and II) a high-energy electron-positron linear collider which acts as a Higgs, top quark and W-boson factory, and that can further be extended to TeV energies. The former could reach a high luminosity that is not accessible at a linear collider, the latter could probe the high energy regime with higher sensitivity and discovery potential than LEP3. The program should be flanked by dedicated intensity frontier searches at lower energies. These accelerators can be used in a feasible, timely and cost-efficient way to search for new physics and make precise determination of the parameters of the Standard Model.

2025-03-21T12:10:55Z Contribution prepared for the 2025 update of the European Strategy for Particle Physics. 8 pages, 1 figure Marco Drewes Elena Shaposhnikova Mikhail Shaposhnikov http://arxiv.org/abs/2503.16269v1 2025-03-20T15:59:55Z

It is known that the alignment of an high-energy e- beam with specific crystal directions leads to a significant increase of the coherent radiation emission. This enhancement can be exploited to create an intense photon source. An elective application is an innovative positron source design for future lepton colliders. Such scheme takes advantage of lattice coherent effects by employing a high-Z crystalline radiator, followed by an amorphous metallic converter, to generate positrons via a two-step electromagnetic process. Additional applications can be in neutron production through photo-transmutation and radionuclide generation via photo-nuclear reactions. In this work, we present experimental results obtained from beam tests at CERN's PS facility using commercial industrial-grade tungsten crystals. The obtained results demonstrate the robust performance of industrial-grade radiators, even with their inherent imperfections, suggesting that it is possible to simplify the supply process and it is not strictly necessary to rely on highly specialized research infrastructures.

2025-03-20T15:59:55Z Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment, Volume 1075, June 2025, 170342 N. Canale M. Romagnoni A. Sytov F. Alharthi S. Bertelli S. Carsi I. Chaikovska R. Chehab D. De Salvador P. Fedeli V. Guidi V. Haurylavets G. Lezzani L. Malagutti S. Mangiacavalli A. Mazzolari P. Monti-Guarnieri R. Negrello G. Paternò L. Perna L. Bandiera 10.1016/j.nima.2025.170342 http://arxiv.org/abs/2503.17396v1 2025-03-18T10:22:56Z

Beamline alignment is challenging as the beamline components must be set up ideally so that the rays follow the desired optical path. Automated methods using a digital twin allow for faster diagnostics and improved beam properties compared to manual tuning. We introduce an automated method of finding the offsets to improve this digital twin model. These offsets represent the unknown but constant differences between the beamline parameter positions as set up at the physical beamline and the corresponding parameter positions of its digital twin. Our method assumes the capability to execute precise relative movements with a known step size for these parameters, although the absolute position information is unknown. By combining the surrogate model with a global optimizer, we successfully determine offsets for 34 beamline parameters on a simulated METRIXS beamline at the BESSY II synchrotron radiation source in Berlin.

2025-03-18T10:22:56Z David Meier Thomas Zeschke Peter Feuer-Forson Bernhard Sick Jens Viefhaus Gregor Hartmann 10.1088/1742-6596/3010/1/012130 http://arxiv.org/abs/2503.13880v1 2025-03-18T04:15:36Z

The evolution from 3rd to 4th generation synchrotron radiation (SR) sources provide promising potential improvements in X-ray techniques, particularly in spatial resolution for imaging, temporal resolution for dynamic studies, and beam size control for nanoprobes. Achieving these enhancements demands effective vibration suppression in beamline systems. This challenge drives the need for optical designs that ensure efficient photon transport while maintaining vibration within acceptable thresholds. To address the advanced coherence requirements of fourth-generation SR sources, wave-optics simulations must be incorporated into optical design processes. We therefore propose a vibration mode propagation method using wave-optics techniques for beamline vibration simulation. Our approach achieves an almost 40-fold computational acceleration in actual beamline models compared to conventional methods, enabling direct analysis of propagating wavefront vibrations. This framework allows systematic evaluation of intensity distribution variations, coherence changes, and beam positioning errors caused by mechanical vibrations.

2025-03-18T04:15:36Z Han Xu Beijing Synchrotron Radiation Facility, Institute of High Energy Physics, Chinese Academy of Sciences, Beijing, People's Republic of China Xiao Li Beijing Synchrotron Radiation Facility, Institute of High Energy Physics, Chinese Academy of Sciences, Beijing, People's Republic of China School of Nuclear Science and Technology, University of Chinese Academy of Sciences, Beijing 100049, China Ming Li Beijing Synchrotron Radiation Facility, Institute of High Energy Physics, Chinese Academy of Sciences, Beijing, People's Republic of China Zhe Ren Beijing Synchrotron Radiation Facility, Institute of High Energy Physics, Chinese Academy of Sciences, Beijing, People's Republic of China Yi Zhang Beijing Synchrotron Radiation Facility, Institute of High Energy Physics, Chinese Academy of Sciences, Beijing, People's Republic of China Peng Liu Beijing Synchrotron Radiation Facility, Institute of High Energy Physics, Chinese Academy of Sciences, Beijing, People's Republic of China Yuhui Dong Beijing Synchrotron Radiation Facility, Institute of High Energy Physics, Chinese Academy of Sciences, Beijing, People's Republic of China Liang Zhou Beijing Synchrotron Radiation Facility, Institute of High Energy Physics, Chinese Academy of Sciences, Beijing, People's Republic of China http://arxiv.org/abs/2503.12154v1 2025-03-15T14:44:49Z

We present the development and integration of a Machine Learning (ML)-based surrogate model, trained on Particle-In-Cell (PIC) simulations of laser-driven plasma wakefield acceleration source of electrons, into Geant4 simulation toolkit. Our model enables the generation and tracking of plasma-accelerated beams within complete experimental setups, unifying plasma acceleration and Monte Carlo-based simulations, which significantly reduces their complexity and computational cost. Our implementation focuses on the PALLAS laser-plasma accelerator test facility, integrating its full experimental setup into Geant4. We describe the ML model, its integration into Geant4, and key simulation results, demonstrating the feasibility of start-to-end simulations of plasma acceleration facilities and applications within a unified framework.

2025-03-15T14:44:49Z A. Sytov K. Cassou V. Kubytskyi M. Lenivenko A. Huber