Decommissioning and Post-Irradiation Examination of the LHC Beam Dumps

2025-07-23T10:09:49Z

The LHC beam dumps are responsible for the safe absorption of the Large Hadron Collider (LHC) particle beams. In 2018, the two 6.4-tonne beam dumps that had been in operation since the LHC's startup in 2008 were removed and replaced with upgraded versions. Endoscopic inspections of these beam dumps and experimental high-intensity proton-beam irradiation of material samples raised concerns about the structural integrity of the carbon-based materials in their cores. It was therefore decided to undertake an accelerated project of dismantling and post-irradiation examination of the removed dumps as part of a wider program of work to ensure the safe operation of the LHC beam dumps in the coming years. This paper describes the decommissioning process for the two beam dumps carried out at CERN between 2021 and 2023, covering the preparatory studies, practical challenges encountered, and solutions implemented. It details the establishment of an operational framework, including the preparation of the working environment, the development of a method for cutting the irradiated 12-mm-thick duplex stainless-steel vessel, and the cut sequencing. Additionally, the paper presents the findings derived from the post-irradiation examination of the different carbon-based core materials subjected to deposited energy densities up to 1.5 kJ/g. The extruded graphite plates within the vessel exhibited a cracking pattern, which was likely due to the dynamic response of the device upon beam impact, and their retaining rings were found to be displaced. Despite minor signs of surface deterioration, the expanded graphite sheets were intact, and the isostatic graphite blocks showed no evidence of material degradation.

Modeling of the positron sources: an experiment-based benchmarking

2025-07-22T15:37:52Z

High-intensity positron sources are critical for next-generation electron-positron colliders, where positron beam quality and characteristics directly impact the luminosity. Accurate modeling and validated simulation tools for positron sources are essential to optimize their performance. However, modeling a positron source tends to be complex, as it involves multiple interdependent stages, from positron production and capture dynamics to beam transport through the injector linac to the collider ring. A reliable simulation framework should integrate these processes to ensure efficient positron production and transport. In this work, we present a start-to-end simulation tool developed for positron sources modeling. The model was benchmarked against existing simulation tools and validated through experimental measurements conducted at the SuperKEKB positron source. Key operational parameters were systematically scanned to evaluate the simulation model performance, including the primary electron impact position on the target, solenoid field strength around the capture linac, and RF phase settings. The primary Figure-of-Merit for all validation tests was the positron yield at the end of the SuperKEKB positron capture section. The simulation results demonstrate a very good agreement with experimental data and other simulation tools, confirming the model's reliability and establishing a framework for future positron source studies.

Reduced Order Hysteretic Flux Model for Transport Current Homogenization in Composite Superconductors

2025-07-21T09:04:43Z

In this paper, we present the Reduced Order Hysteretic Flux (ROHF) model to describe the relationship between time-varying transport current and internal magnetic flux for composite superconductors. The ROHF model is parametrized using reference simulations of the conductor response, after which it enables the computation of macroscopic quantities such as voltage and power loss without requiring detailed electromagnetic field solutions. It is therefore suitable for the homogenization of transport current effects in large-scale superconducting magnets, avoiding a fine discretization of the composite strand small scale structures, allowing to drastically reduce the computational effort. The approximation can be implemented either (i) as a rate-independent model, neglecting eddy current effects in the normal conducting matrix, or (ii) as a rate-dependent model, including those eddy current effects. In this paper, the complete modeling workflow, including parameter identification, coupling with the other fields (temperature and magnetic field), and post-processing of the results, is described and verified using a twisted multifilamentary strand as an example.

Efficient ultrafast photoacoustic transduction on Tantalum thin films

2025-07-21T09:01:18Z

Nano-acoustic strain generation in thin metallic films via ultrafast laser excitation is widely used in material science, imaging and medical applications. Recently, it was shown that transition metals, such as Titanium, exhibit enhanced photoacoustic transduction properties compared to noble metals, such as Silver. This work presents experimental results and simulations that demonstrate that among transition metals Tantalum exhibits superior photoacoustic properties. Experiments of nano-acoustic strain generation by femtosecond laser pulses focused on thin Tantalum films deposited on Silicon substrates are presented. The nano-acoustic strains are measured via pump-probe transient reflectivity that captures the Brillouin oscillations produced by photon-phonon interactions. The observed Brillouin oscillations are correlated to the photoacoustic transduction efficiency of the Tantalum thin film and compared to the performance of Titanium thin films, clearly demonstrating the superior photoacoustic transduction efficiency of Tantalum. The findings are supported by computational results on the laser-induced strains and their propagation in these thin metal film/substrate systems using a Two-Temperature Model in combination with thermo-mechanical Finite Element Analysis. Finally, the role of the metal transducer-substrate acoustic impedance matching is discussed and the possibility to generate appropriately modulated acoustic pulse trains inside the crystalline substrate structures for the development of crystalline undulators used for γ-ray generation is presented.

Zeptosecond Gamma-Ray Pulses Generation via FEL-Driven Microbunching and Laser-Compton Scattering

2025-07-21T07:06:53Z

We introduce a novel and reliable approach to generate zeptosecond(10^{-21} s,zs), high-energy photon pulse bursts by synergistically exploiting the inherent characteristics of Free-Electron Lasers (FELs) and laser-Compton scattering. The feasibility of this scheme is validated through comprehensive numerical simulations. In a representative simulation, a 4 GeV electron beam, undergoing the FEL process, emits radiation at 0.7 nm and develops a microbunched structure. These microbunches subsequently interact with a 2 ps, 9 micrometers laser pulse in a head-on Compton scattering configuration. Our simulation results demonstrate that under conditions of well-established electron beam microbunching, the proposed method successfully yields high-brightness gamma-photon pulse bursts with durations approaching 800 zeptoseconds and exhibiting exceptional signal-to-noise ratios, consistent with theoretical expectations. This technique opens up avenues for exploring ultrafast nuclear dynamics and provides unprecedented perspectives for delving into the Quantum Zeno and Anti-Zeno effects.

Coherent deflection of elliptic bunches colliding at crossing angle

2025-07-18T19:46:07Z

The coherent deflection of charged particles bunch in the field of an counter-propagating bunch is considered. Bunches collide at non-zero crossing angle and they have different energies. Charge distributions in both colliding bunches are Gaussian. The generalization of Bassetti-Erskine formalism for bunch deflection and orbit shift is derived. Applications in collider physics are discussed.

Crystal Collimation Cleaning Measurements with 6.5 TeV protons in the LHC

2025-07-17T17:33:31Z

Safe disposal of beam halo is a fundamental requirement of modern superconductive hadron colliders to reduce thermal load on magnets and background to experimental detectors. In the CERN Large Hadron Collider (LHC) a multistage system fully compliant with the needs of the baseline operation was build. At a later stage, two short bent crystals were interleaved to the devices for betatron collimation to investigate efficiency enhancement of the halo disposal when inserting them as primary stages of the collimation hierarchy. Each crystal was mounted on a high--accuracy angular actuator, called goniometer, and installed in the clockwise Beam 1, one for the horizontal and one for the vertical plane. In this paper, measurements of the cleaning performance at collision energy with and without inserting crystals in the standard collimation schemes are discussed; the results are compared to theoretical expectations.

Dechanneling Population at Extreme Crystal Bending with 6.5 TeV Proton Beam

2025-07-17T15:59:40Z

Beam measurements with bent crystals, installed in the Large Hadron Collider to assist multistage collimation system, provided information on hadron interactions with crystals in the multi-TeV energy range. In particular, the dechanneling population was observed through scans of deflected halo with collimators. Taking advantage of the fact that crystals with different values of curvature radii were present, the dependence of dechanneling on bending radius (R) was recorded. Dechanneling was found to be enhanced in crystals with smaller bending radius, because it is too close to the critical value R_c at the LHC energy of 6.5 TeV where channeling is lost. Data analysis and comparison to simulation results provided a better understanding of the phenomena and could be used to define specifications for more performing crystals in future upgrades of the crystal collimation system.

ILC250 Cost Update -- 2024

2025-07-17T12:46:15Z

The International Linear Collider was conceived as a global project for an energy-frontier electron-positron collider.It employs superconducting RF and nano-beam technologies with a center-of-mass energy of 500 GeV. Its cost was estimated in 2013, based on the Technical Design Report published in 2013.Japan's high-energy community proposed to host the ILC in Japan as a Higgs boson factory at 250 GeV in its first phase, and a revised cost estimate was conducted in 2017 to host it in Japan. However, due to global price increases and currency fluctuations that emerged afterward, the 2017 estimate is now outdated. A new cost evaluation has therefore been performed, according for global inflation tends, exchange rate shifts, and recent experiences in SRF based accelerators. This report describes the cost update performed in 2024. The cost update is included in the ILC Status Report in May 2025, contributing to the ongoing 2026 update of the European Strategy for Particle Physics.

Observation and Interpretation of Field Emission Saturation Induced by an Ultra-fast Intense Terahertz Field

2025-07-17T01:32:19Z

Field emission under ultra-fast intense terahertz fields provides a promising approach for generating electron bunches with ultrashort pulse duration and high charge densities. It is generally believed that the field emission current described by traditional field emission theory increases dramatically with the applied electric field. However, we conducted extensive field emission experiments using quasi-single-cycle strong-field terahertz radiation at various energy levels and different temperatures and observed an intriguing phenomenon where the emitted charge reached saturation. A novel model is proposed to interpret this phenomenon, which considers the contribution of surface valence electrons and the dynamic replenishment of free electrons from the bulk to the surface. The experimentally observed convex relationship between the emitted charge and terahertz energy is consistent with the model prediction, unlike the concave relationship derived from the traditional field emission formula. In addition, another observed counter-intuitive phenomenon, the inverse correlation between the cathode temperature and saturated emission charge, is also well interpreted by the model. This work offers comprehensive insights into field emission dynamics under ultra-fast intense fields, paving the way for generating electron bunches with unprecedented temporal resolution.

Two-dimensional Light Beam Shape Characterization using Interferometric Closure Amplitudes

2025-07-16T17:42:35Z

We introduce a novel technique using closure amplitudes, inspired by radio interferometry, to determine with high angular resolution the two-dimensional profile of a light beam using an interferogram from a non-redundantly masked aperture. Previous techniques have required multiple interferograms or accurate estimates of the non-uniform illuminations across the aperture. In contrast, our method using closure amplitudes avoids the need to estimate the aperture illuminations while determining the two-dimensional beam shape from a single interferogram. The invariance of closure amplitudes to even time-varying aperture illuminations makes it suitable to longer averaging intervals, with potential to reducing data rates and computational overheads. By using data from the ALBA synchrotron light source to validate the method and its results against existing methods, this paper represents the first real-world application of closure amplitudes to directly determine the light beam's profile using optical interferometry in the high angular resolution regime.

Study of the transfer and matching line for a PWFA-driven FEL

2025-07-16T15:47:49Z

The development of compact accelerator facilities providing high-brightness beams is one of the most challenging tasks in the field of next-generation compact and cost affordable particle accelerators. Recent results obtained at SPARC\_LAB show evidence of the FEL laser by a compact (3 cm) particle driven plasma-based accelerator. This work is carried out in the framework of the SPARC\_LAB activities concerning the R$\&$D on plasma wakefield accelerators for the realization of new compact plasma based facilities, i.e EuPRAXIA@SPARC\_LAB. The work here presented is a theoretical study demonstrating a possible scheme concerning the implementation of an innovative array of discharge capillaries, operating as active-plasma lenses, and one collimator to build an unconventional transport line for bunches outgoing from plasma accelerating module. Taking advantage of the symmetric and linear focusing provided by an active-plasma lens, the witness is captured and transported along the array without affecting its quality at the exit of the plasma module. At the same time the driver, being over-focused in the same array, can be removed by means of a collimator.

Advanced Space Mapping Technique Integrating a Shared Coarse Model for Multistate Tuning-Driven Multiphysics Optimization of Tunable Filters

2025-07-16T11:47:35Z

This article introduces an advanced space mapping (SM) technique that applies a shared electromagnetic (EM)-based coarse model for multistate tuning-driven multiphysics optimization of tunable filters. The SM method combines the computational efficiency of EM single-physics simulations with the precision of multiphysics simulations. The shared coarse model is based on EM single-physics responses corresponding to various nontunable design parameters values. Conversely, the fine model is implemented to delineate the behavior of multiphysics responses concerning both nontunable and tunable design parameter values. The proposed overall surrogate model comprises multiple subsurrogate models, each consisting of one shared coarse model and two distinct mapping neural networks. The responses from the shared coarse model in the EM single-physics filed offer a suitable approximation for the fine responses in the multiphysics filed, whereas the mapping neural networks facilitate transition from the EM single-physics field to the multiphysics field. Each subsurrogate model maintains consistent nontunable design parameter values but possesses unique tunable design parameter values. By developing multiple subsurrogate models, optimization can be simultaneously performed for each tuning state. Nontunable design parameter values are constrained by all tuning states, whereas tunable design parameter values are confined to their respective tuning states. This optimization technique simultaneously accounts for all the tuning states to fulfill the necessary multiple tuning state requirements. Multiple EM and multiphysics training samples are generated concurrently to develop the surrogate model. Compared with existing direct multiphysics parameterized modeling techniques, our proposed method achieves superior multiphysics modeling accuracy with fewer training samples and reduced computational costs.

Strategy for Bayesian Optimized Beam Steering at TRIUMF-ISAC's MEBT and HEBT Beamlines

2025-07-15T17:01:07Z

In preparation for operation of multiple Rare Isotope Beams (RIBs) when the Advanced Rare Isotope Laboratory (ARIEL) becomes operational, TRIUMF embarked on a program of advanced beam tuning applications and machine learning tools. The strategy for operationalizing Bayesian Optimization for beam steering purposes is being developed. A previously reported centroid correction algorithm is used to tune accelerated charged particle beams at TRIUMF's ISAC postaccelerator facility. We present findings and results from multiple machine development experiments conducted between October and November 2024, as part of a pivot toward semi-automated machine tuning methods. These findings were instrumental in shaping the tuning strategy for the medium and high energy beam transport (MEBT, HEBT) lines at ISAC, by sequentially optimizing sub-sections of the beamlines.

Recovery of hydrogen plasma at the sub-nanosecond timescale in a plasma-wakefield accelerator

2025-07-15T11:43:25Z

Plasma wakefield acceleration revolutionized the field of particle accelerators by generating gigavolt-per-centimeter fields. To compete with conventional radio-frequency (RF) accelerators, plasma technology must demonstrate operation at high repetition rates, with a recent research showing feasibility at megahertz levels using an Argon source that recovered after about 60 ns. Here we report about a proof-of-principle experiment that demonstrates the recovery of a Hydrogen plasma at the sub-nanosecond timescale. The result is obtained with a pump-and-probe setup and has been characterized for a wide range of plasma densities. We observed that large plasma densities reestablish their initial state soon after the injection of the pump beam (< 0.7 ns). Conversely, at lower densities we observe the formation of a local dense plasma channel affecting the probe beam dynamics even at long delay times (> 13 ns). The results are supported with numerical simulations and represent a step forward for the next-generation of compact high-repetition rate accelerators.