https://arxiv.org/api/Y9BIuqPHRvWhOyeRiXiTJlFY9tA 2026-03-22T08:57:37Z 38731 30 15 http://arxiv.org/abs/2603.17817v1 2026-03-18T15:09:13Z

The aim of this paper is to provide a comparison of channel characteristics for vehicle-to-vehicle (V2V) communication at 60 GHz and 80 GHz frequency bands in a high-mobility scenario where two vehicles pass each other in opposite directions. The study is based on measurements of the time-varying channel impulse response capturing the behavior of multi-path propagation during vehicle motion. By directly comparing these two frequency bands under identical measurement conditions, we attempt to quantify the differences in power delay profile, root mean square (RMS) delay spread, RMS Doppler spread, and intervals (regions) of stationarity in time domain. The results show that these bands do not differ significantly, but the 80 GHz band exhibits somewhat greater RMS delay spread and RMS Doppler spread when calculated over the entire delay-Doppler spectrum, and conversely exhibits shorter stationarity regions. However, the characteristics of the measurement setup in the two bands and their influence on comparative measurements must be considered. In particular, attention must be paid to the impact of antennas.

2026-03-18T15:09:13Z 7 pages, 8 figures, 2 tables 2025 IEEE Future Networks World Forum (FNWF), Bangalore, India, November 10-12, 2025 Ales Prokes Tomas Mikulasek Josef Vychodil Radek Zavorka Jiri Blumenstein Jaroslaw Wojtun Jan M. Kelner Cezary Ziolkowski Aniruddha Chandra 10.1109/FNWF66845.2025.11317288 http://arxiv.org/abs/2603.17766v1 2026-03-18T14:26:21Z

This paper presents results from a vehicle-to-vehicle channel measurement campaign conducted in the millimeter-wave (MMW) frequency bands at center frequencies of 60GHz and 80GHz, each with a bandwidth of 2GHz. The measurements were performed in a dynamic oncoming-vehicle scenario using a time-domain channel sounder with high-resolution data acquisition. Power delay profiles were extracted to study the temporal evolution of multipath components, and the root mean square (RMS) delay spread was analyzed to characterize the temporal dispersion of the channel. The results demonstrate differences between the two frequency bands. At 60GHz, the RMS delay spread is well approximated by a Gaussian distribution with a higher median value, while at 80GHz it follows a lognormal distribution with a lower median. Furthermore, the number of resolvable multipath components was found to be nearly twice as high at 60\,GHz compared to 80GHz, highlighting the impact of antenna beamwidth and frequency-dependent propagation mechanisms.

2026-03-18T14:26:21Z 6 pages, 7 figures 2025 IEEE Conference on Antenna Measurements and Applications (CAMA), Antibes, France, November 18-20, 2025 Radek Zavorka Tomas Mikulasek Josef Vychodil Jiri Blumenstein Hussein Hammoud Jaroslaw Wojtun Aniruddha Chandra Markus Hofer Jan M. Kelner Cezary Ziolkowski Christoph Mecklenbrauker Ales Prokes http://arxiv.org/abs/2603.17762v1 2026-03-18T14:22:56Z

Polarization diversity offers significant flexibility for enhancing integrated sensing and communications (ISAC). However, conventional dual-polarized arrays typically require dedicated radio-frequency (RF) chains for each polarization branch, leading to prohibitive hardware costs. To address this, polarization-reconfigurable (PR) antennas have emerged as a cost-effective alternative, enabling polarization flexibility with reduced hardware complexity by driving two polarization branches with a single RF chain. In this paper, we investigate fairness-aware beamforming for ISAC systems equipped with PR antennas. Specifically, we jointly optimize the transmit beamforming and PR control coefficients to maximize the minimum signal-to-interference-plus-noise ratio (SINR) for communication users and the minimum signal-to-clutter-plus-noise ratio (SCNR) for sensing targets. The resulting problem is highly nonconvex and nonsmooth due to the strong coupling among optimization variables in the max-min objective, as well as the nonconvex spherical constraints imposed by the PR antennas. To tackle this, we derive an equivalent smooth reformulation by introducing auxiliary variables and transforming the minimum operators into inequality constraints. Subsequently, we develop an exact-penalty product Riemannian manifold gradient descent (EP-PRMGD) algorithm, which integrates an exact penalty method with Riemannian optimization to guarantee convergence to a Karush-Kuhn-Tucker (KKT) point. Numerical results demonstrate that the proposed PR-enabled ISAC scheme achieves performance comparable to dual-polarized architectures while utilizing only half the RF chains, thereby validating its effectiveness in balancing fairness and hardware efficiency.

2026-03-18T14:22:56Z Weijie Xiong Jingran Lin Di Jiang Cunhua Pan Hongli Liu Kai Zhong Qiang Li http://arxiv.org/abs/2502.05021v7 2026-03-18T14:16:26Z

Can stochastic gradient methods track a moving target? We study the problem of tracking multidimensional time-varying parameters under noisy observations and possible model misspecification. Gradient-based filters update the time-varying parameters using the gradient of a postulated objective function. A natural filtering objective is the logarithm of the postulated observation density, which gives rise to the widely used class of score-driven filters. As in the optimization literature, these filters come in two forms: explicit filters evaluate the gradient at the predicted parameter, whereas implicit filters evaluate it at the updated parameter. For both filter types, we derive novel sufficient conditions for exponential stability of the filtered parameter path, showing that stability can be guaranteed independently of the data-generating process. Under mild additional moment conditions on the data-generating process, we also obtain finite-sample and asymptotic mean squared error bounds relative to the pseudo-true parameter path. For implicit filters, these guarantees hold under weak parameter restrictions. For explicit filters, they additionally require Lipschitz continuity of the score and a sufficiently small learning rate. Simulation studies support our theoretical findings and show that implicit gradient filters outperform explicit ones in both accuracy and stability.

2025-02-07T15:48:16Z 62 pages Simon Donker van Heel Rutger-Jan Lange Bram van Os Dick van Dijk http://arxiv.org/abs/2603.17744v1 2026-03-18T14:11:58Z

Integrated sensing and communication (ISAC) has emerged as a key paradigm for next-generation wireless systems, which allows wireless resources to be used for data transmission and target sensing simultaneously. In this paper, multi-user collaborative target detection in the uplink ISAC system is investigated. To incorporate the target sensing functionality, the system relies on the reuse of uplink signals from the communication users. Specifically, we analyze an uplink multi-user single-input multiple-output (MU-SIMO) communication system with bistatic sensing. Using the channel statistics, we formulate the problem of joint optimal pilot and data power allocation to maximize the uplink ergodic sum rate while meeting communication and sensing quality-of-service (QoS) requirements. To address this non-convex problem, we propose an alternating optimization (AO)-based iterative framework, where the joint power allocation problem is decomposed into two sub-problems. Specifically, the pilot power allocation is optimized using a penalty dual decomposition (PDD)-based gradient ascent algorithm, while the data power allocation is solved via successive convex approximation (SCA). Once the long-term power allocation is determined, the base station (BS) estimates the instantaneous channels using a minimum mean-squared error (MMSE) estimator. Subsequently, based on the estimated instantaneous channel state information (CSI), the receive beamforming for communication users is optimized via another SCA-based method to maximize the sum rate. Meanwhile, the optimal receive beamforming for the target is obtained in closed-form through eigenvalue decomposition (EVD).

2026-03-18T14:11:58Z Ling He Vaibhav Kumar Roberto Bomfin Yingyang Chen Miaowen Wen Marwa Chafii http://arxiv.org/abs/2603.17658v1 2026-03-18T12:25:58Z

This work investigates antenna coding optimization to enhance the channel capacity of single-input single-output orthogonal frequency division multiplexing (SISO-OFDM) systems empowered by highly reconfigurable pixel antennas. We first introduce the model for pixel antenna empowered SISO-OFDM systems using a beamspace channel representation. We next formulate the problem to maximize the channel capacity through jointly optimizing antenna coding and the power allocation across subcarriers and solve it by Successive Exhaustive Boolean Optimization (SEBO) and water-filling (WF) algorithm. To reduce computational complexity, a codebook-based approach is also proposed for antenna coding optimization. Simulation results show that the channel capacity of SISO-OFDM system across all signal-to-noise-ratio (SNR) regions considered can be enhanced through leveraging pixel antennas as compared to using conventional antenna with fixed configuration. This result demonstrates the effectiveness of antenna coding technology empowered by pixel antenna in enhancing SISO-OFDM systems.

2026-03-18T12:25:58Z 6 pages, 4 figures, conference Tianrui Qiao Shanpu Shen Yijun Chen Ross Murch http://arxiv.org/abs/2603.17622v1 2026-03-18T11:39:52Z

A novel generative site-specific beamforming (GenSSBF) approach, termed fast beam-brainstorm (F-BBS), is proposed to address the practical bottlenecks of slow beam generation and fixed channel probing lengths in existing GenSSBF. To accelerate beam generation, F-BBS utilizes a two-stage distillation strategy that learns an average velocity field, instead of an instantaneous one, to guide the beam generative process. This strategy enables larger generation steps, realizing few-step or even one-step beam generation. Furthermore, to accommodate flexible channel probing lengths, a stochastic masking mechanism and a beam index-aware masked condition encoder are proposed, enabling a single trained model to operate with variable-length channel probing observations without retraining. Therefore, FBBS achieves the fast generation of high-fidelity communication beams from coarse and variable-length channel probing feedback, i.e., reference signal received power (RSRP), from user equipments. Simulation results on accurate ray-tracing datasets show that 1) F-BBS achieves comparable performance while reducing the beam generation cost by over 90% compared with diffusion-based GenSSBF solutions, 2) F-BBS realizes robust performance across variable channel probing length, and 3) FBBS offers a desirable trade-off between beamforming gain and beam probing overhead.

2026-03-18T11:39:52Z Zihao Zhou Zhaolin Wang Yuanwei Liu http://arxiv.org/abs/2603.17620v1 2026-03-18T11:34:38Z

Recently a novel multi-antenna architecture termed ray antenna array (RAA) was proposed, where several simple uniform linear arrays (sULAs) are arranged in a ray-like structure to enhance communication and sensing performance. By eliminating the need for phase shifters, it also significantly reduces hardware costs. However, RAA is prone to signal blockage and has no elevation angle resolution capability in three-dimensional (3D) scenarios. To address such issues, in this paper we propose a novel spherical directly-connected antenna array (DCAA), which composes of multiple simple uniform planar arrays (sUPAs) placed over a spherical surface. All elements within each sUPA are directly connected. Compared to conventional arrays with hybrid analog/digital beamforming (HBF), DCAA significantly reduces hardware cost, improves energy focusing, and provides superior and uniform angular res olution for 3D space. These advantages make DCAA particularly suitable for integrated sensing and communication (ISAC) in low-altitude unmanned aerial vehicles (UAV) swarm scenarios, where targets may frequently move away from the boresight of traditional arrays, degrading both communication and sensing performance. Simulation results demonstrate that the proposed spherical DCAA achieves significantly better angular resolution and higher spectral efficiency than conventional array with HBF, highlighting its strong potential for UAV swarm ISAC systems.

2026-03-18T11:34:38Z Haoyu Jiang Zhenjun Dong Zhiwen Zhou Yong Zeng http://arxiv.org/abs/2603.17616v1 2026-03-18T11:29:51Z

Conventional hybrid beamforming architectures are often compared with one another and with the fully-digital architecture under the same \emph{radiated} antenna power. However, the physically relevant budget is the power injected by the RF-chain outputs into the passive analog RF network, which is then usually transferred to the antenna ports in a contractive (lossy) manner. This issue is especially pronounced for fully-connected splitter--phase-shifter--combiner networks, whose physical power transfer remains contractive even under ideal passive-component assumptions. Motivated by this injected-power viewpoint, this paper proposes a hybrid beamforming architecture based on a programmable unitary RF network. Under ideal passive-component assumptions, all injected RF-chain power reaches the antenna ports without loss. The analog RF network is realized as an \emph{interlaced mixer--phase} architecture consisting of fixed (non-programmable) mixing layers interleaved with programmable diagonal phase-shifting layers. We derive a closed-form digital beamformer and a low-complexity programming method for the analog beamformer, yielding a hybrid precoder that closely matches the fully-digital precoder. Narrowband simulations with continuous and quantized phases, benchmarked against the fully-digital architecture, the physically modeled fully-connected phase-shifter baselines, and an ideal-lossless Butler/DFT beam-selection baseline under equal total injected RF-chain power, show that the continuous-phase and 6-bit realizations of the proposed architecture are nearly indistinguishable from the fully-digital benchmark and achieve significant gains over the baseline hybrid beamforming architectures.

2026-03-18T11:29:51Z Nikola Zlatanov Damir Salakhov http://arxiv.org/abs/2511.01747v3 2026-03-18T11:21:38Z

Photoplethysmography (PPG) is widely used as a non-invasive and accessible modality for continuous health monitoring. However, despite being a peripheral hemodynamic signal intrinsically coupled with systemic circulation, existing research has largely confined its scope to a narrow range of cardiovascular tasks, leaving a fundamental question underexplored: to what extent can PPG support holistic health profiling beyond traditional cardiovascular applications? To answer this question, we present AnyPPG, a foundation model-based framework designed to reveal the broader health-profiling potential of PPG. To ensure reliable performance for this investigation, AnyPPG is pretrained with ECG guidance on the most diverse PPG corpus with synchronized ECG to date, comprising over 100,000 hours of recordings from six large-scale data sources. This pretraining yields robust and physiologically grounded PPG representations that provide a reliable basis for subsequent analysis. Building upon this pretrained model, we conduct a systematic investigation into the association between PPG and holistic health through, to our knowledge, the first PPG-based phenome-wide disease detection study, spanning 1,468 disease phenotypes in more than 15,000 subjects. Our evaluation demonstrates the effectiveness of AnyPPG: across eight clinical and wearable datasets covering 15 downstream tasks, it achieves the best performance in 13 tasks. More importantly, in the phenome-wide analysis, AnyPPG exhibits meaningful discriminative capability (AUC $\ge$ 0.70) for 307 phenotypes across 16 distinct phecode chapters, including 230 non-circulatory conditions such as dementia and chronic kidney disease, many of which have rarely been explored using PPG. Collectively, these findings indicate that easily acquired PPG signals encode rich health-related information extending well beyond conventional cardiovascular assessment.

2025-11-03T16:59:01Z Guangkun Nie Xiaocheng Fang Gongzheng Tang Yujie Xiao Jun Li Bo Liu Hongyan Li Shenda Hong http://arxiv.org/abs/2603.17526v1 2026-03-18T09:31:06Z

This article presents a fully 3D-printed wideband metasurface folded reflectarray antenna (MFRA) operating in the millimeter-wave n257 band. The proposed MFRA integrates a novel polarization-rotating reflective metasurface (RMS), a compact embedded horn feed, and a polarization-selective metasurface polarization grid (MPG), all fabricated using a low-cost in-house 3D-printed method. Unlike conventional PCB-based FRAs constrained to planar unit-cell geometries, the proposed anisotropic meta-element design exploits full three-dimensional dielectric control by tailoring varying unit-cell heights. This volumetric tuning, combined with the spatial distribution of the meta-elements, enables phase compensation exceeding $400^{\circ}$ across the aperture, supporting robust wideband performance. An MFRA prototype is in-house fabricated and experimentally validated. Measured results agree well with simulations, achieving a $-10$ dB impedance bandwidth of 20.7\% (26--32 GHz) and a peak realized gain of 31.1 dBi at 28.2 GHz. The antenna exhibits sidelobe levels below $-20$ dB, cross-polarization below $-30$ dB, and a compact height-to-diameter ratio of 0.20. Stable pencil beams with an average HPBW of $3.7^{\circ}$ are maintained across the operating band. To further validate the robustness of the proposed in-house designed MFRA, a commercially manufactured RMS was also obtained, whose measured performance shows excellent agreement with the in-house 3D-printed version, confirming a cost-effective rapid-prototyping antenna solution. The proposed MFRA is a cost-effective solution for beyond 5G and 6G high-gain point-to-point mmWave wireless applications, such as fixed wireless access, near field communication, and beam focusing.

2026-03-18T09:31:06Z 8 pages, 10 figures, 1 table Evangelos Vassos Thomas Whittaker Abdul Jabbar Aakash Bansal Will Whittow http://arxiv.org/abs/2603.17499v1 2026-03-18T09:00:25Z

The integration of artificial intelligence into next-generation wireless networks necessitates the accurate construction of radio maps (RMs) as a foundational prerequisite for electromagnetic digital twins. A RM provides the digital representation of the wireless propagation environment, mapping complex geographical and topological boundary conditions to critical spatial-spectral metrics that range from received signal strength to full channel state information matrices. This tutorial presents a comprehensive survey of learning-based RM construction, systematically addressing three intertwined dimensions: data, paradigms, and physics-awareness. From the data perspective, we review physical measurement campaigns, ray tracing simulation engines, and publicly available benchmark datasets, identifying their respective strengths and fundamental limitations. From the paradigm perspective, we establish a core taxonomy that categorizes RM construction into source-aware forward prediction and source-agnostic inverse reconstruction, and examine five principal neural architecture families spanning convolutional neural networks, vision transformers, graph neural networks, generative adversarial networks, and diffusion models. We further survey optics-inspired methods adapted from neural radiance fields and 3D Gaussian splatting for continuous wireless radiation field modeling. From the physics-awareness perspective, we introduce a three-level integration framework encompassing data-level feature engineering, loss-level partial differential equation regularization, and architecture-level structural isomorphism. Open challenges including foundation model development, physical hallucination detection, and amortized inference for real-time deployment are discussed to outline future research directions.

2026-03-18T09:00:25Z Xiucheng Wang Yuhao Pan Nan Cheng http://arxiv.org/abs/2602.10537v2 2026-03-18T05:33:00Z

Integrated sensing and communication (ISAC) can substantially improve spectral, hardware, and energy efficiency by unifying radar sensing and data communications. In wideband and scattering-rich environments, clutter often dominates weak target reflections and becomes a fundamental bottleneck for reliable sensing. Practical ISAC clutter includes "cold" clutter arising from environmental backscatter of the probing waveform, and "hot" clutter induced by external interference and reflections from the environment whose statistics can vary rapidly over time. In this article, we develop a unified wideband multiple-input multiple-output orthogonal frequency-division multiplexing (MIMO-OFDM) signal model that captures both clutter types across the space, time, and frequency domains. Building on this model, we review clutter characterization at multiple levels, including amplitude statistics, robust spherically invariant random vector (SIRV) modeling, and structured covariance representations suitable for limited-snapshot regimes. We then summarize receiver-side suppression methods in the temporal and spatial domains, together with extensions to space-time adaptive processing (STAP) and space-frequency-time adaptive processing (SFTAP), and we provide guidance on selecting techniques under different waveform and interference conditions. To move beyond reactive suppression, we discuss clutter-aware transceiver co-design that couples beamforming and waveform optimization with practical communication quality-of-service (QoS) constraints to enable proactive clutter avoidance. We conclude with open challenges and research directions toward environment-adaptive and clutter-resilient ISAC for next-generation networks.

2026-02-11T05:16:32Z 36 pages, 12 figures. Accepted by Proceedings of the IEEE Rang Liu Peishi Li Ming Li A. Lee Swindlehurst http://arxiv.org/abs/2603.17369v1 2026-03-18T05:21:38Z

To address the challenges of high-dimensional channel estimation and underutilized spatial correlations among users in holographic MIMO (HMIMO) systems, this paper proposes a joint graph-cut algorithm for multi-user channel estimation in the wavenumber domain. The size of the conventional angular domain channel matrix increases with the number of antennas in densely-spaced HMIMO. Therefore, user channels are projected into the wavenumber domain via a Fourier harmonic transform, revealing their inherent clustered sparsity and exploiting common scatterer clusters among users. Subsequently, a joint graph-cut channel estimation (JGC-CE) algorithm based on multi-user common supports is designed. In each iteration, the algorithm first partitions user clusters to extract shared supports. Then for each user, it performs users' individual graph update and channel estimation to reconstruct the channel matrix. Simulation results demonstrate that the proposed method outperforms independent estimation schemes for individual users in accuracy while reducing pilot length.

2026-03-18T05:21:38Z Jiaxin Zhang Wenqian Shen Kai Yang Zhen Gao Jianping An http://arxiv.org/abs/2603.17317v1 2026-03-18T03:21:37Z

We study the exact decision problem for feedback capacity of finite-state channels (FSCs). Given an encoding $e$ of a binary-input binary-output rational unifilar FSC with specified rational initial distribution, and a rational threshold $q$, we ask whether the feedback capacity satisfies $C_{fb}(W_e, π_{1,e}) \ge q$. We prove that this exact threshold problem is undecidable, even when restricted to a severely constrained class of rational unifilar FSCs with bounded state space. The reduction is effective and preserves rationality of all channel parameters. As a structural consequence, the exact threshold predicate does not lie in the existential theory of the reals ($\exists\mathbb{R}$), and therefore cannot admit a universal reduction to finite systems of polynomial equalities and inequalities over the real numbers. In particular, there is no algorithm deciding all instances of the exact feedback-capacity threshold problem within this class. These results do not preclude approximation schemes or solvability for special subclasses; rather, they establish a fundamental limitation for exact feedback-capacity reasoning in general finite-state settings. At the metatheoretic level, the undecidability result entails corresponding Gödel-Tarski-Löb incompleteness phenomena for sufficiently expressive formal theories capable of representing the threshold predicate.

2026-03-18T03:21:37Z Angshul Majumdar